Filter
Top Products
8
<DRB1349>
PART NAMES AND FUNCTIONS
5 CH-1 equalizer dials (HI/MID/LOW)
HI
Use to adjust CH-1 input treble response (range of adjustment:
13 kHz, +6 dB to –26 dB).
MID
Use to adjust CH-1 input midrange response (range of
adjustment: 1 kHz, +6 dB to –26 dB).
LOW
Use to adjust CH-1 input bass response (range of adjustment:
70 Hz, +6 dB to –26 dB).
6 MIC SEND button and indicator
When set to On, the indicator lights, and microphone signals
are output at the SEND jacks. This function is disabled when
the CH-1 input selector switch is set to [MIC].
7 Session input level dial (SESSION IN)
Use to adjust the session input volume (range of adjustment:
0 dB to –∞).
8 CH-1 SEND button and indicator
When set to On, the indicator lights, and CH-1 signals are
output at the SEND jacks.
9 CH-1 EQ ON/OFF switch and indicator
When set to [ON], the indicator lights and CH-1 equalizer is
enabled.
When set to [OFF], the indicator goes out and the equalizer
circuit is bypassed.
10 CH-2 input selector switch
(CH-1 – PHONO 2/LINE 2 – CD 2)
Use to select input signal from CH-1 (component selected
with CH-1 input selector switch), CH-2 PHONO/LINE input
jacks, or CH-2 CD input jacks, and send them to the TRIM
control.
* When [CH-1] is selected, signals are sent to the CH-2 TRIM
control without being sent through the CH-1 TRIM control.
11 CH-2 TRIM dial
Use to adjust the CH-2 input signal level (range of
adjustment: +9 dB to –∞).
12 MASTER LEVEL dial
User to adjust the master output volume level (range of
adjustment: 0 dB to –∞).
13 Booth monitor level dial
(BOOTH/SESSION OUT)
Use to adjust the volume level of signals at the BOOTH/
SESSION OUT jacks (range of adjustment: 0 dB to –∞).
This level can be set independently of the setting of the
MASTER LEVEL dial.
14 Headphones level dial (PHONES)
Use to adjust the volume level of the headphones output
(range of adjustment: 0 dB to –∞).
15 Monitor SELECT switch
MASTER position
selects MASTER output. (This setting allows output
regardless of the setting of the MASTER LEVEL dial.)
EFFECT position
Regardless of the [ON/OFF] setting of the EFFECT switch,
the output is the signal selected with CUE, with effects
added.
CUE position
selects the channel adjusted with the headphone mixing
lever (17).
16 CH-2 equalizer dials (HI/MID/LOW)
HI
Use to adjust CH-2 input treble response (range of
adjustment: 13 kHz, +6 dB to –26 dB).
MID
Use to adjust CH-2 input midrange response (range of
adjustment: 1 kHz, +6 dB to –26 dB).
LOW
Use to adjust CH-2 input bass response (range of
adjustment: 70 Hz, +6 dB to –26 dB).
17 Headphone mixing lever (CH-1 – CH-2)
This lever does not function when the monitor SELECT
switch (15) is set to [MASTER].
When the monitor SELECT switch (15) is set to [EFFECT] or
[CUE], moving the lever to the left side produces CH-1
monitor output, while moving it to the right produces CH-2
monitor output. Centering the lever at the center detent
position produces balanced output of CH-1 and CH-2 signals.
18 CH-2 SEND button and indicator
When set to On, the indicator lights, and CH-2 signals are
output at the SEND jacks.
19 CH-2 EQ ON/OFF switch and indicator
When set to [ON], the indicator lights and the CH-2 equalizer
is enabled.
When set to [OFF], the indicator goes out and the equalizer
circuit is bypassed.
20 CH-1 FADER START button
When this button is set to On, fader start and back cue can be
performed on the CH-1 CD player.
Whether the operation is initiated by operation of the CH-1
fader lever, or by the cross fader lever is determined by the
position of the front panel’s FADER START selector switch;
the selection is indicated by the lighting of the top panel’s
CH-1 FADER START indicator or C.F.1 FADER START
indicator.
* For DJ CD players supporting the fader start/back cue
function, see page 5, “1. Connecting Input Components”.
21 CH-1 output On/Off lever (TRANSFORM)
Use to set CH-1 output to On or Off (Mute).
The lever’s setting angle can be changed in 45° increments
(changing of the angle should be performed by an authorized
Pioneer service technician).