Filter
Top Products
9
Português Italiano DeutschNederlands Español Français
English
EXT SPEAKER (CUBE-120XL BASS only)
1. EXT SPEAKER Jack
This is for connecting an external speaker.
When an external speaker is connected, sound is played both from the
external speaker and from the unit’s built-in speaker.
* When connecting to an external speaker, make sure the speaker
conforms to the following speci cations.
Impedance: 8 ohms or less
Allowable power input: 120 watts or greater
* Only use speaker cable to connect the speaker. Do not use any
shielded cable designed for use with guitars.
LINE OUT/DI OUT
2. LINE OUT Jack (CUBE-60XL BASS)
This is for connecting a PA system, recorder, or other external
equipment.
This features COSM speaker modeling, enabling production of
impressive bass-amp sound.
You can use this in conjunction with an external PA system, or to
record your performance via direct line while monitoring the sound
from the CUBE’s speaker.
* The sound from AUX IN is not output from LINE OUT jack.
3. DI OUT Jack (CUBE-60XL BASS)
Use this to connect to external PAs and other such systems. Signals
input to the BASS INPUT jack are output as is.
This professional-grade feature includes a tough, reliable XLR-type
connector and ground lift switch.
4. LINE OUT/DI OUT Jack (CUBE-120XL BASS)
Use this to connect to external PAs and other such systems.
This professional-grade feature includes a tough, reliable XLR-type
connector and ground lift switch.
5. LINE OUT/DI OUT [SELECT] Switch (CUBE-120XL BASS)
You can switch the sound that is output from the CUBE-120XL BASS’s
LINE OUT/DI OUT to suit the particular application.
Switch Description
DI OUT
Signals input to the BASS INPUT jack are output as is. Other
than the PAD switch, none of the CUBE’s knobs a ect the
LINE OUT/DI OUT output.
LINE OUT The sound is changed by the settings of the CUBE’s knobs.
6. [GND LIFT] Switch
Loop hum noise may occur when other external devices are connected
to the CUBE-60XL/CUBE-120XL. In such instances, you may be able
to mitigate the problem by switching the position of the [GND LIFT]
switch. The [GND LIFT] switch should be normally set to OFF.
Switch Description
ON Pin 1 is disconnected from the CUBE’s ground.
OFF Pin 1 connects to the CUBE’s ground.
RECORDING OUT/PHONES
7. RECORDING OUT/PHONES Jack
This functions either as an output jack for recording or as aphones
jack.
This features COSM speaker modeling, enabling production of
impressive bass sound.
Adjust the volume using the [VOLUME] knobs for the COSM AMP and
the SOLO function.
* When a plug is connected to this jack, no sound is played from
either the unit or any connected external speaker. This is handy at
night or in other situations when you want to avoid high-volume
sound from the speakers.
When using as an output jack for recording
Use a monaural 1/4” phone plug to connect a recorder or other
recording device.
When using as a headphones jack
Connect headphones.
FOOT SW
By connecting a foot switch (BOSS FS-5U or FS-6; sold separately),
you’ll be able to use your foot to turn COMP/DRIVE, EFX, REVERB,
and DELAY on/o , and control the LOOPER function. The connection
diagram at the previous page is a connection example that shows
how to use a momentary-type foot switch (FS-5U, FS-6). For details on
connections and settings when using a latch-type foot switch (BOSS
FS-5L; sold separately), refer to “Using a Latch-type Foot Switch” (p. 11).
8. TIP: DELAY/REC/PLAY/DUB
RING: TAP/STOP
Switch Description
TIP
If the [DELAY/LOOPER] knob is in the DELAY area, the DELAY will
be switched on/o .
If the knob is in the LOOPER area, the foot switch will have the
same function as the panel’s [REC/PLAY/DUB] switch.
RING
The foot switch will have the same function as the [TAP/STOP]
switch.
* You must use a momentary-type foot switch with the RING (TAP/
STOP) of this jack. It will not work correctly with a latch-type foot
switch (p. 11).
9. TIP: EFX
RING: REVERB
Switch Description
TIP
The foot switch will turn on/o the e ect selected by the [EFX]
knob.
RING
The foot switch will turn on/o the REVERB set by the [REVERB]
knob.
10. TIP: SOLO
RING: COMP/DRIVE
Switch Description
TIP The foot switch will turn SOLO on/o .
RING
The foot switch will turn on/o the compression or drive set by
the [COMP/DRIVE] knob.