Filter
Top Products
72
Adding effects
10: LIMITER
The limiter compresses signals that exceed a specified volume level,
preventing distortion from occurring.
fig.MFX-10
11: HEXA-CHORUS
Hexa-chorus uses a six-phase chorus (six layers of chorused sound)
to give richness and spatial spread to the sound.
fig.MFX-11
12: TREMOLO CHO (Tremolo Chorus)
Tremolo chorus is a chorus effect with added tremolo (cyclic
modulation of volume).
fig.MFX-12
Parameter
Value Description
Threshold
0–127 Adjusts the volume at which
compression will begin.
Release 0–127 Adjusts the time from when the
volume falls below the Thresh-
old Level until compression is
no longer applied.
Ratio 1.5:1, 2:1, 4:1,
100:1
Adjusts the compression ratio.
Pan # L64–63R Adjusts the stereo location of the
output sound.L64 is far left, 0 is
center, and 63R is far right.
Post Gain 0, +6, +12, +18
[dB]
Adjusts the output gain.
Low Gain -15– +15 [dB] Adjusts the gain of the low fre-
quency.
High Gain -15– +15 [dB] Adjusts the gain of the high fre-
quency.
Level # 0–127 Adjusts the output level.
Parameter Value Description
Pre Delay
0.0–100 [ms] Adjusts the time delay from
when the direct sound begins
until the chorus sound is heard.
Rate # 0.05–10.00 [Hz] Adjusts the rate of modulation.
Depth 0–127 Adjusts the depth of modula-
tion.
Pre Delay Dev 0–20 Pre Delay Deviation adjusts the
differences in Pre Delay be-
tween each chorus sound.
Pre Delay determines the time
from when the direct sound be-
gins until the processed sound is
heard.
Depth Dev -20– +20 Adjusts the difference in modu-
lation depth between each cho-
rus sound.
L in
R in
L out
R out
Pan R
Pan L
Limiter
2-Band
EQ
Balance W
Balance W
L in
R in
L out
R out
Hexa-Chorus
Balance D
Balance D
Pan Dev
0–20 Adjusts the difference in stereo
location between each chorus
sound.
With a setting of 0, all chorus
sounds will be in the center. With
a setting of 20, each chorus sound
will be spaced at 60 degree inter-
vals relative to the center.
Balance # D100:0W–
D0:100W
Adjusts the volume balance be-
tween the direct sound and the
chorus sound.
With a setting of D100:0W only the
direct sound will be output, and
with a setting of D0:100W only the
chorus sound will be output.
Level 0–127 Adjusts the output level.
Parameter
Value Description
Pre Delay
0.0–100 [ms] Adjusts the time delay from
when the direct sound begins
until the chorus sound is heard.
Cho Rate 0.05–10.00 [Hz] Adjusts the modulation speed of
the chorus effect.
Cho Depth 0–127 Adjusts the modulation depth of
the chorus effect.
Treml Rate # 0.05–10.00 [Hz] Adjusts the modulation speed of
the tremolo effect.
Treml
Separation
0–127 Adjusts the spread of the tremo-
lo effect.
Phase 0–180 [deg] Adjusts the spread of the tremo-
lo effect.
Balance # D100:0W–
D0:100W
Adjusts the volume balance be-
tween the direct sound and the
tremolo chorus sound.
With a setting of D100:0W only
the direct sound will be output,
and with a setting of D0:100W
only the tremolo chorus sound
will be output.
Level 0–127 Adjusts the output level.
Parameter
Value Description
Tremolo Chorus
L in
R in
L out
R out
Balance D
Balance D
Balance W
Balance W
RS-50_e3.book 72 ページ ２００３年１１月７日 金曜日 午後７時１分