36
Initial IP configuration
IP models of the ServSwitch CX family possess a further collection of
configuration options related specifically to IP networking. It is important that
the options are correctly set up for your installation BEFORE being connected to
an open IP network.
To configure IP-specific settings
1
From a local user port (for security reasons, the IP configuration option
cannot be accessed from remote user ports), log on as ‘admin’ user.
2 Press
(hotkeys can be changed).
3 Press
to select ‘More menus’.
4 Select ‘Functions’ and then select ‘Configure IP port’.
• If the unit is being configured for the first time or following a reset,
the unit will display the first of five screens, as shown opposite
• If the unit has been previously
IP-configured it will display the
IP Configuration menu, as
shown below
SERVSWITCHCX
Unit Config
Hardware Rev 1
Firmware 1.0b7
Keyboard UK
AdminPwd
Unit Name
Time 11: 14: 44
Date 27 Apr 2006
Encryption PreferOff
Screen1 of 5
-Up -Down
Next
Space-Toggle
SERVSWITCHCX
SecureKeys
Random data is required to
generate encryption keys for
secure VNC access.
Please move the mouse or
press keys until the bar
becomes full.
– – – – – – – – – – – – –
Screen4 of 5
SERVSWITCHCX
NetworkConfig
MacAddr 00:0F:58:40:07:FE
Use DHCP No
IPAddress 192.168.1.22
Net Mask 255.255.255.0
Gateway
VNC Port 5900
HTTP Port 80
-Up -Down
Enter-Edit
Space-Toggle
Screen2 of 5
Next
SERVSWITCHCX
ModemConfig
ServerIP 192.168.3.1
ClientIP 192.168.3.2
Baud Rate 115200
InitString ATZS0=1
Initialize Port
RestoreDefaults
Enter-Select
-Up -Down
Esc-Exit
Space-Toggle
Screen3 of 5
Next
SERVSWITCHCX
Configuration
Unit Configuration
NetworkConfiguration
ModemConfiguration
ResetConfiguration
Back
Enter-Select
-Up -Down
Esc-Exit
See Configure IP port for details.
To use the initial IP-configuration sequence
Set the options in each screen and then select Next to proceed.
Admin password
Enter a password of at least six characters that has a mix
of letters and numerals. The background colour provides
an indication of password suitability and is initially red
to indicate that the password is not sufficient. When a
password with reasonable strength has been entered it
will change to green.
Time and Date
Set these correctly as all entries in the activity log are time
stamped using them.
Encryption
See Encryption settings for a description of the issues
and the settings.
Use DHCP/IP address/Net Mask/Gateway
You need to either set the DHCP option to ‘Yes’ or
manually enter a valid IP address, Net mask and Gateway.
See Networking issues for more details.
VNC and HTTP ports
These should remain set to 5900 and 80, respectively,
unless they clash with an existing setup within the
network. See Networking issues for more details.
Modem/ISDN port details
The default items here are perfectly adequate for
the majority of modem and ISDN terminal adapter
installations.
The Server IP and Client IP addresses are used to form an
isolated two-device PPP network connection via the dial
up link. Their settings are not related to any other ‘real’
network settings within the ServSwitch CX with IP unit.
Secure keys generation
With every mouse move and keypress, the single dash will
move across the screen (unless the same key is pressed
repeatedly). Periodically, a new star character will be
added to the bar as the random data are accepted as
part of the new encryption key. When the bar is full, the
final encryption keys for your ServSwitch CX with IP will
be created – this process takes roughly 30 to 40 seconds.
Once the secure keys have been calculated the ServSwitch
CX with IP will show the IP configuration menu.
1
2
3
4
Note: Screen 5 of 5 is
displayed while the secure
keys are being generated.
