Filter
Top Products
22. GND (GROUND TERMINAL) -
Connect each of your turntables ground leads to either of the two
ground terminal. This will reduce the humming and popping noises associated with magnetic phono
cartridges.
23. CHANNEL 2: PHONO 2 INPUT JACKS -
Connect turntables equipped with MM pickup cartridge
to PHONO inputs only (All DJ turntable use MM pick-up cartridges). CD players or Tape Decks and
other line level instruments should not be connected to these jacks. The red colored RCA jack repre-
sents the right channel input and the white represents the left channel input.
24. CHANNEL 1: PHONO 1 INPUT JACKS -
Connect turntables equipped with MM pickup cartridge
to PHONO inputs only (All DJ turntable use MM pick-up cartridges). CD players or Tape Decks and
other line level instruments should not be connected to these jacks. The red colored RCA jack repre-
sents the right channel input and the white represents the left channel input.
25. RCA BOOTH OUTPUTS JACKS -
T
hese RCA jacks send a low current unbalanced output signal
and are controlled by the
BOOTH LEVEL (13)
volume control. These jacks should only be used for
shorter cable runs to signal processors or looping to another mixer.
26. CHANNEL 4: LINE 5 INPUT JACKS -
These Jacks are used for line level inputs. Connect CD
players or Tape Decks to LINE inputs. Line level musical instruments with stereo outputs such as
Rhythm Machines or Samplers should also be connected to LINE inputs. Turntables should only be
connected to “Phono” inputs. The red colored RCA jack represents the right channel input and the
white represents the left channel input. Volume will be controlled by the channel four
FADER (4).
27. CHANNEL 3: LINE 3 INPUT JACKS -
These Jacks are used for line level inputs. Connect CD
players or Tape Decks to LINE inputs. Line level musical instruments with stereo outputs such as
Rhythm Machines or Samplers should also be connected to LINE inputs. Turntables should only be
connected to “Phono” inputs. The red colored RCA jack represents the right channel input and the
white represents the left channel input. Volume will be controlled by the channel three
FADER (4).
28. CHANNEL 2: LINE 2 RCA INPUT JACKS -
These Jacks are used for line level inputs. Connect
CD players or Tape Decks to LINE inputs. Line level musical instruments with stereo outputs such as
Rhythm Machines or Samplers should also be connected to LINE inputs. Turntables should only be
connected to “Phono” inputs. The red colored RCA jack represents the right channel input and the
white represents the left channel input. Volume will be controlled by the channel three
FADER (4).
29. CHANNEL 1: LINE 1 RCA INPUT JACKS -
These Jacks are used for line level inputs. Connect
CD players or Tape Decks to LINE inputs. Line level musical instruments with stereo outputs such as
Rhythm Machines or Samplers should also be connected to LINE inputs. Turntables should only be
connected to “Phono” inputs. The red colored RCA jack represents the right channel input and the
white represents the left channel input. Volume will be controlled by the channel three
FADER (4).
30. MICROPHONE 1 CONNECTOR -
This jack is used to a connect a microphone to the mixer. Con-
nect you microphone via 1/4 inch (6.3mm) jack. The signal volume will be controlled by the
MIC 1
VOLUME KNOB (1)
.
31. MICROPHONE 2 CONNECTOR -
This jack is used to a connect a microphone to the mixer. Con-
nect you microphone via 1/4 inch (6.3mm) jack. The signal volume will be controlled by the
MIC 2
VOLUME KNOB (1)
.
DX4™ Controls and Features Cont.
©
American Audio
®
- www.americandj.com - DX4™ Instruction Manual Page 8