American Audio Pro-Scratch 2 Musical Instrument User Manual


  Open as PDF
of 36
 
Storing A Cue Point:
Once you have set your CUE Point by one of the two means listed on page 16, you may store your cue point
in one of the FLASH BUTTONS (8). Once you store this cue point in memory you may recall it at any time and
you may even recall if the disc has been remove or power had been disconnected. You may store a maximum
of three cue points per a disc and maximum of 384 cue points can be saved in unit's memory. The MEMORY
BUCKET (55) in the LCD DISPLAY (19) will approximate the available memory. Either a CUE POINT or a
SAMPLE (See creating a sample loop on page 17) can be stored into a FLASH BUTTON (8), not both. To
Store a cue point:
1) Create a Cue Point by one of the two means listed on page 14. Press the MEMORY BUTTON (9), as
in Figure 17. The red Memory Cue LED will glow indicating the store memory function has been activated.
You may now press any one of the three FLASH BUTTONS (8) to store your cue point into memory (Figure
18). After pressing one of the FLASH BUTTONS (8), the corresponding Flash Button LED will flash briefly.
The LED on the above the FLASH BUTTON (8) will remain lit indicating either a sample or cue point is stored
in memory. The red Memory LED will turn off.
2) Repeat the above steps to store up to three Cue Points. Once your three cue points have been stored
you may access them at any time. During playback the cue points will instantly start playback from that
point without any music interruption. Please note in order to access these cue point, the disc used to
create the cue points must be in the drive.
10.CREATING AND PLAYING A SEAMLESS LOOP
A seamless loop is a sound loop that plays continuously without sound interruption. You can use this loop to
create dramatic effect in your mixing. This loop has no time limit and you could actually loop the entire length
of disc. You create a seamless loop between two continuous points of a disc.
BASIC OPERATIONS (CONT.)
Figure 18
Figure 17
2) Press the IN BUTTON
(14). This will set the
starting point of the
SEAMLESS LOOP. The
IN BUTTON (14) LED
will light.
1) Press PLAY/PAUSE
BUTTON (17) to
activate playback
mode
Figure 20
Figure 19
©American Audio® - www.americandj.com - Pro-Scratch 2™ Instruction Manual Page 17
PARAMETER TIME
PARAMETER RATIO
EJECT
POWER
CUE
1 2 3 4 5 6 7 8 9 0
RELOOP
SINGLE
LOOP
REMAIN
NONSTOP
TOTALELAPSED
M
T
S
PROGRAM
LOCK
KEY
SYNC.BEAT
F
PITCH
BPM
CUE
AUTO
BPM
OFF
ON
FX
MIX
BOP
ENTER
PANFLANGERSKID PHASE
FX SELECT
SGL/CTN
TIME REV.PLAY
TEMPO
LOCK
4%/8%/16%
TRANSECHOSCRATCH FILTER HOLD
ON/OFF
SAMPLE PITCH
PARAMETER TIME
PARAMETER RATIO
EJECT
POWER
CUE
1 2 3 4 5 6 7 8 9 0
RELOOP
SINGLE
LOOP
REMAIN
NONSTOP
TOTALELAPSED
M
T
S
PROGRAM
LOCK
KEY
SYNC.BEAT
F
PITCH
BPM
CUE
AUTO
BPM
OFF
ON
FX
MIX
BOP
ENTER
PANFLANGERSKID PHASE
FX SELECT
SGL/CTN
TIME REV.PLAY
TEMPO
LOCK
4%/8%/16%
TRANSECHOSCRATCH FILTER HOLD
ON/OFF
SAMPLE PITCH
PARAMETER TIME
PARAMETER RATIO
EJECT
POWER
CUE
1 2 3 4 5 6 7 8 9 0
RELOOP
SINGLE
LOOP
REMAIN
NONSTOP
TOTALELAPSED
M
T
S
PROGRAM
LOCK
KEY
SYNC.BEAT
F
PITCH
BPM
CUE
AUTO
BPM
OFF
ON
FX
MIX
BOP
ENTER
PANFLANGERSKID PHASE
FX SELECT
SGL/CTN
TIME REV.PLAY
TEMPO
LOCK
4%/8%/16%
TRANSECHOSCRATCH FILTER HOLD
ON/OFF
SAMPLE PITCH
PARAMETER TIME
PARAMETER RATIO
EJECT
POWER
CUE
1 2 3 4 5 6 7 8 9 0
RELOOP
SINGLE
LOOP
REMAIN
NONSTOP
TOTALELAPSED
M
T
S
PROGRAM
LOCK
KEY
SYNC.BEAT
F
PITCH
BPM
CUE
AUTO
BPM
OFF
ON
FX
MIX
BOP
ENTER
PANFLANGERSKID PHASE
FX SELECT
SGL/CTN
TIME REV.PLAY
TEMPO
LOCK
4%/8%/16%
TRANSECHOSCRATCH FILTER HOLD
ON/OFF
SAMPLE PITCH
 previous next