Filter
Top Products
©American Audio® - www.americandj.com - Pro-Scratch 2™ Instruction Manual Page 29
BUILT-IN EFFECTS
Figure 54
Figure 56
HOLD BUTTON: Use the HOLD BUTTON (2) to lock your customized param-
eters. If the hold button is not activated any changes to your parameters will be
momentary. To activate the hold function press the HOLD BUTTON (2) as in
figure 56. When the hold function becomes activated, the hold button will begin
to glow blue.
PARAMETER TIME
PARAMETER RATIO
EJECT
POWER
CUE
1 2 3 4 5 6 7 8 9 0
RELOOP
SINGLE
LOOP
REMAIN
NONSTOP
TOTALELAPSED
M
T
S
PROGRAM
LOCK
KEY
SYNC.BEAT
F
PITCH
BPM
CUE
AUTO
BPM
OFF
ON
FX
MIX
BOP
ENTER
PANFLANGERSKID PHASE
FX SELECT
SGL/CTN
TIME REV.PLAY
TEMPO
LOCK
4%/8%/16%
TRANSECHOSCRATCH FILTER HOLD
ON/OFF
SAMPLE PITCH
PARAMETER TIME
PARAMETER RATIO
EJECT
POWER
CUE
1 2 3 4 5 6 7 8 9 0
RELOOP
SINGLE
LOOP
REMAIN
NONSTOP
TOTALELAPSED
M
T
S
PROGRAM
LOCK
KEY
SYNC.BEAT
F
PITCH
BPM
CUE
AUTO
BPM
OFF
ON
FX
MIX
BOP
ENTER
PANFLANGERSKID PHASE
FX SELECT
SGL/CTN
TIME REV.PLAY
TEMPO
LOCK
4%/8%/16%
TRANSECHOSCRATCH FILTER HOLD
ON/OFF
SAMPLE PITCH
PARAMETER TIME
PARAMETER RATIO
EJECT
POWER
CUE
1 2 3 4 5 6 7 8 9 0
RELOOP
SINGLE
LOOP
REMAIN
NONSTOP
TOTALELAPSED
M
T
S
PROGRAM
LOCK
KEY
SYNC.BEAT
F
PITCH
BPM
CUE
AUTO
BPM
OFF
ON
FX
MIX
BOP
ENTER
PANFLANGERSKID PHASE
FX SELECT
SGL/CTN
TIME REV.PLAY
TEMPO
LOCK
4%/8%/16%
TRANSECHOSCRATCH FILTER HOLD
ON/OFF
SAMPLE PITCH
PARAMETERS:
All the effects have adjustable parameters. The parameters change the way the
effect will react. To enter the parameters menus for any of the effects, press or
turn either of the two PARAMETER KNOBS (1 OR 3) as in figure 55. When the
parameter mode is selected the time display in the LCD (19) will change to indi-
cate the parameter your are adjusting. All effects except the pan effect have two
adjustable parameters. Parameter Time (1) and parameter ratio (3). Use these
knobs to customize the effects to your liking.
Figure 55
TRANS/PAN EFFECT: The TRANS effect simulates a real-time mixer transformer
effect. When the "Transformer" effect is activated the TRANS/PAN BUTTON (21) will
glow green, when the "Pan" effect is selected the button will glow red. The PAN effect
allows you to pan the output from the left channel to the right channel.
TRANS EFFECT: The TRANS Effect has two adjustable parameters, Parameter
Time and Parameter Ratio. The PT will adjust the Trans Speed and The PR will
adjust the Trans Audio Length. The lower the PT value the faster the TRANS effect
(PT 0500 = 1/2 second, PT 1000 = 1 second).
PAN EFFECT: The PAN effect uses the PT value to pan left to Right. PT 0500
is the default setting which is center pan. The Pan Value ranges from 10ms to ten
seconds.