Casio WK3500 Musical Instrument User Manual


 
A-20
Appendix
735A-E-134A
3 : Depth(Range: -64 to 0 to +63)
Adjusts the depth of the wah in accordance
with the level of the input signal.
Setting a positive value causes the wah filter
to open in direct proportion with the size of
the input signal, producing a bright sound.
Setting a negative value causes the Wah filter
to close in accordance with the size of the in-
put signal, which produces a dark tone qual-
ity. However, large input re-opens the Wah fil-
ter, even if it is closed.
06 :Compressor
Function
Compresses the input signal, which can have
the effect of suppressing level variation and
making it possible to sustain dampened
sounds longer.
Parameters
0 : Depth (Range: 0 to 127)
Adjusts compression of the audio signal.
1 : Attack (Range: 0 to 127)
Adjusts the attack amount of the input signal.
A smaller value causes prompt compressor
operation, which suppresses the attack of the
input signal.
A larger values delays compressor operation,
which causes attack to be output as-is.
2 : Release (Range: 0 to 127)
Adjusts the time from the point when the in-
put signal drops below a certain level until the
compression operation is stopped.
When an attack feeling is desired (no compres-
sion at the onset of the sound), set this param-
eter to as low a value as possible.
To have compression applied at all times, set a
high value.
3 : Level (Range: 0 to 127)
Adjusts the output level.
The output volume changes in accordance with
the Depth setting and the characteristics of the
input tone. Use this parameter to correct for
such changes.
07 :Limiter
Function
This is an effector that you can use to set an
upper limit value on the level of the input sig-
nal.
Parameters
0 : Limit (Range: 0 to 127)
Adjusts the volume level from which the limit
is applied.
1 : Attack (Range: 0 to 127)
Adjusts the attack amount of the input signal.
2 : Release (Range: 0 to 127)
Adjusts the time from when the input signal
drops below a certain level until the limit op-
eration stops.
3 : Level (Range: 0 to 127)
Adjusts the level being output.
The output volume changes in accordance with
the Limit setting and the characteristics of the
input tone. Use this parameter to correct for
such changes.
08 :Distortion
Function
This effect provides Distortion +
AmpSimulator.
Parameters
0 : Gain (Range: 0 to 127)
Adjusts the input gain.
1 : Low (Range: 0 to 127)
Adjusts the low-band gain.
The cutoff frequency differs according to the
preset DSP.
2 : High (Range: 0 to 127)
Adjusts the high-band gain.
The cutoff frequency differs according to the
preset DSP.
3 : Level (Range: 0 to 127)
Adjusts the output level.
09 :Stereo Phaser
Function
This is a stereo phaser that modulates the phase
in accordance with a sine wave LFO.
Parameters
0 : Resonance (Range: 0 to 127)
Adjusts the resonance of the sound.
1 : Manual (Range: -64 to 0 to +63)
Adjusts the phaser shift volume, which is used
for reference.
2 : Rate (Range: 0 to 127)
Adjusts the rate of the LFO.
3 : Depth (Range: 0 to 127)
Adjusts the depth of the LFO.
4 : Wet Level (Range: 0 to 127)
Adjusts the volume level of the effect.
10 :Phaser
Function
This is a monaural phaser that modulates the
phase in accordance with a sine wave LFO.
Parameters
0 : Resonance (Range: 0 to 127)
Adjusts the resonance of the sound.
1 : Manual (Range: -64 to 0 to +63)
Adjusts the phaser shift volume, which is used
for reference.
WK3000_e_A-19-31.p65 04.3.26, 0:12 PM20