Filter
Top Products
10
Playback
The playback method will depend on the effect
program you have selected.
For a program in the “SAMPLE/PLAY” group
1. Select a program of the “SAMPLE/PLAY”
group (90–99).
2. Press the [SAMPLE 1] or [SAMPLE 2] key
that you want to play back. You will not hear
the playback at this time.
3. When you touch the touch-pad, playback will
occur according to the position you touch.
The way in which the phrase plays back will
depend on the program. (☞separate sheet
“Effect Program List)
4. Use the [FX BALANCE] knob to adjust the
volume of the playback.
If the [FX BALANCE] knob is in the center
position, the playback sound and the input
sound will be output in a 1:1 proportion.
Setting the knob to the maximum position
will output only the sample sound when
playing; the input sound will not be heard.
For a program not in the “SAMPLE/PLAY” group
1. Select a program not in the “SAMPLE/
PLAY” group.
2. When you press the [SAMPLE 1] or
[SAMPLE 2] key, recorded phrase will play
back at normal speed. If you continue
holding down the key, the playback will
loop.
To adjust the volume, hold down the
[SAMPLE 1] or [SAMPLE 2] key and turn the
[FX BALANCE] knob.
By operating the touch-pad during playback,
you can apply effects to the playback sound.
If you hold down the [SAMPLE 1] or
[SAMPLE 2] key and press the [HOLD] key,
the playback will be held. Hold will be
cancelled when you press the [SAMPLE 1] or
[SAMPLE 2] key once again.
14. Displaying the audio
waveform or a composite
pattern
You can display the waveform of the audio input
signal or audio output signal. In addition, patterns
built into the KAOSS PAD Entrancer can be used
instead of the video input as material for modification.
Pattern Display mode
Hold down the [FUNCTION] key and press
the [SAMPLE 1] key to enter Pattern Display
mode; the [PROGRAM/BPM] display will
blink indicate either Pattern Display mode or
the pattern select number.
If you display a pattern while playing back a
motion video sample, playback will stop.
When you play back the sample once again,
pattern display mode will be cancelled and
the sample will play back.
Exiting Pattern Display mode
To return to normal operation, either touch
the touch-pad, press the [FUNCTION] key,
or simply do not operate the KAOSS PAD
Entrancer for ten seconds.
Displaying a pattern
From Pattern Display mode, press one of the
[PROGRAM MEMORY 1–8] keys to recall the
pattern that is pre-selected for that key.
You can press the [SAMPLE 1] key to turn
the last-selected pattern on/off.
To cancel the display
To cancel the display, press the selected
[PROGRAM MEMORY 1–8] key once again.
The display will also be cancelled if you
switch programs during normal operation.
The display will be not cancelled if you hold
down the [FUNCTION] key and turn the
program knob to change programs.
Effect clip patterns (40–59) will appear when
you operate the touch pad.
Switching patterns
In Pattern Display mode, you can hold down
one of the [PROGRAM MEMORY 1–8] keys
and turn the [PROGRAM/BPM] knob to
switch the pattern that is assigned to that
key. If that key is selected, you can simply
turn the [PROGRAM/BPM] knob to switch
patterns.
Storing the modified settings
In Pattern Display mode, press and hold the
[REC/STOP] key for one second or longer to
store the modified settings. The settings of
MIDI Edit mode will also be stored at this
time. If you turn off the power without
storing, the settings will revert to their
previous state.
To stop the pattern display from being turned off when
you change programs
Hold down the HOLD key while you turn on
the power. (The HOLD key will light for a
short time.)
To cancel
Turn off the power, and then turn it on in the
normal way.
Pattern types
00–39: Impose patterns
These layer a superimposed pattern (such as
the waveform of the input signal, or touch
pad position information) onto the image.
You cannot apply an effect to the imposed
pattern or sample it.
40–59: Effect clip patterns
These patterns display color patterns or
image data. You can use these as effect
materials.
If you have selected a program from other
than the “SAMPLE/PLAY” group, you
cannot display these except while recording.