Filter
Top Products
3
We realize that you must have a powerful
hankerin’ to try out your new CR1604-VLZ.
Or you might be one of those people who
never reads manuals. Either way, all we ask
is that you read this page NOW, and the rest
can wait until you’re good and ready. But do
read it — you’ll be glad you did.
Other Nuggets of Wisdom
For optimum sonic performance, the channel
faders and the
MAIN L-R MIX
fader should be
set near the “
U
” (unity gain) markings.
Always turn the
MAIN L-R MIX
fader and
C–R/
PHONES
knob down before making connections
to and from your CR1604-VLZ.
If you shut down your equipment, turn off
your amplifiers first. When powering up, turn
on your amplifiers last.
Save the shipping box! You may need it
someday, and you don’t want to have to pay for
another one.
INSTANT MIXING
Here’s how to get going
right away, assuming you own
a microphone and a keyboard:
1. Plug your microphone into Channel 1’s
MIC
input.
2. Turn on the CR1604-VLZ.
3. Perform the Level-Setting Procedure .
4. Connect cords from the
MAIN OUT
jacks
to your amplifier.
5. Hook up speakers to the amp and turn it on.
6. Set channel 1’s fader to the “U” mark.
7. Engage (push in) Channel 1’s
L-R
switch.
8. Set the
MAIN L-R MIX
fader one-quarter
of the way up.
9. Sing like a canary!
10. Plug your keyboard into channels 3 and 4.
11. Turn channel 3’s
PAN
knob fully left and
channel 4’s
PAN
knob fully right.
12. Set those faders to the “U” mark.
13.
Perform the Level-Setting Procedure .
14.
Engage the
L-R
switch on these channels.
15. Play like a madman and sing like a canary!
It’s your first mix!
READ THIS PAGE!!!
Please write your serial number here for
future reference (i.e. insurance claims, tech
support, return authorization, etc.):
Part No. 820-034-00 Rev. C 4/97
©1997 Mackie Designs, All Rights Reserved.
Printed in the U.S.A.
LEVEL-SETTING PROCEDURE
Message to seasoned pros: do NOT set lev-
els using the old “Turn the trim up until the
clip light comes on, then back off a hair” trick.
When a Mackie Designs mixer clip light
comes on, you really are about to clip.
This procedure really works — it assures
low noise and high headroom. Please read on.
It’s not even necessary to hear what you’re
doing to set optimal levels. But if you’d like to:
Plug headphones into the
PHONES
output
jack, then set the
C-R PHONES
knob about
one-quarter of the way up.
The following steps must be performed
one channel at a time:
1. Turn the
TRIM
,
AUX
send and fader
controls fully down.
2. Be sure the
1–2
,
3–4
and
L–R
channel
assignment switches are all disengaged.
3. Set the
EQ
knobs at the center detents.
4. Connect the signal source to the
MIC
or
LINE
channel input.
5. Engage (push in) the channel’s
SOLO
switch.
6. Push in the
MODE
switch in the output
section (
LEVEL SET (PFL)
mode) —
the
LEVEL SET
LED will light.
7. Play something into the selected input,
at real-world levels.
8. Adjust the
TRIM
control so that the
display on the meter stays around “0.”
(Only the left meter is active in the
Level-Setting Procedure.)
9. If you’d like to apply some
EQ
, do so
now and return to the previous step.
10. Disengage that channel’s
SOLO
switch.
11. Repeat for each of channels 1–16.
Purchased at:
Date of purchase: