Filter
Top Products
9
GB
Sub woofer selection
Initial setting is : SUB WOOFER [YES]
• If you connect a sub woofer, select “YES” to output the
LFE (low frequency effect) channel from the sub woofer.
• If you do not connect a sub woofer, select “NO”. This
activates the MPEG/Dolby Digital (AC-3) bass redirection
circuitry and outputs the LFE signals from other speakers.
• In order to take full advantage of the Dolby Digital (AC-3)
bass redirection circuitry, we recommend setting the sub
woofer’s cut off frequency as high as possible. (However,
when using an amplifier with 5.1 ch inputs, set the sub
woofer’s cut off frequency to match the characteristics of
the amplifier.
Front speaker distance
Initial setting is : FRONT 5.0 meter
Set the distance from your listening position to the front (left
or right) speaker (A on page 7).
• Front speaker distance can be set in 0.1 metre steps from
1.0 to 12.0 metres.
• If both speakers are not placed an equal distance from
your listening position, set the distance to the closest
speaker.
Centre speaker distance
Initial setting is : CENTER 5.0 meter
Set the distance from your listening position to the centre
speaker.
• Centre speaker distance can be set in 0.1 metre steps from
a distance equal to the front speaker distance (A on page
7) to a distance 1.5 metres closer to your listening position
(B on page 7).
• Do not place the centre speaker farther away from your
listening position than the front speakers.
Rear speaker distance
Initial setting is : REAR 3.5 meter
Set the distance from your listening position to the rear (left
or right) speaker.
• Rear speaker distance can be set in 0.1 metre steps from a
distance equal to the front speaker distance (A on page 7)
to a distance 4.5 metres closer to your listening position
(C on page 7).
• Do not place the rear speakers farther away from your
listening position than the front speakers.
• If both speakers are not placed an equal distance from
your listening position, set the distance to the closest
speaker.
z To manually adjust the bass roll off frequency for
each channel
When the front, centre, or rear speaker sizes are set to
small, the bass roll off frequency is automatically set to
120 Hz. To select a different roll off frequency, set the
menu mode to EXPAND and use the front, centre, or
rear speaker roll off parameters in the speaker set up
menu.
For details about the menu mode, see page 15.
For details about the roll off parameters, see page 19.
Adjusting the speaker volume
Use the remote while seated in your listening position
to adjust the volume of each speaker.
Note
This unit incorporates a new test tone with a frequency
centred at 800 Hz for easier speaker volume adjustment.
1 Press TEST.
You will hear the test tone from each speaker in
sequence.
2 From your listening position, use the remote to
adjust the volume of each speaker so that the test
tone can be heard at the same level from all
speakers.
A
Press FRONT BAL L or R to adjust the balance
between the front left and right speakers (±8
dB, 0.5 dB/steps).
During this adjustment, the test tone is emitted
from both speakers simultaneously.
B
Press REAR BAL L or R to adjust the balance
between the rear left and right speakers (±8 dB,
0.5 dB/steps).
During this adjustment, the test tone is emitted
from both speakers simultaneously.
C
Press CENTER + or – to adjust the level of
centre speaker (0.5 dB/steps).
During this adjustment, the test tone is emitted
from the centre speaker.
D
Press REAR + or – to adjust the level of rear
speakers (0.5 dB/steps).
During this adjustment, the test tone is emitted
from both speakers simultaneously.
3 Press TEST to turn off the test tone.
Getting Started
1, 3
2
B
2
C
2
D
2
A
MASTER
VOLUME
(continued)