Filter
Top Products
18 Example setups
EMX860ST—Owner’s Manual
As a band PA
Here is an example of using the EMX860ST as a small PA for a band. In this example, an external effect such
as delay or reverb is also being used.
Connections
• Connect mics or instruments, such as keyboards,
to the channel input jacks 1–8.
• Connect the main speakers to the SPEAKERS L/
R’s A/B jacks, and connect the monitor speakers
to the SPEAKERS MONITOR’s A/B jacks.
• Connect the monitor speakers to the SPEAKERS
MONITOR A/B jacks.
• If you will be using an external effect such as
delay or reverb, connect the EMX860ST’s
EFFECT OUT jack to the input jack of the exter-
nal effect, and connect the output jack of the
external effect to the EMX860ST’s AUX IN jack.
SEE REAR PANEL CAUTION.
POWER
PHANTOM
+48V
ON
OFF
+6
+3
0
–5
–10
+6
+3
0
–5
–10
•
6
•
0
•
6
•
MONI
ON
LR
LR
LIMITER
LIMITER
VOCAL
L HALL
S HALL
L+R
BRIDGE
STEREO
MAIN
MASTER
EFFECT RTN
MONITOR
EFFECT
REC
OUT
TAPE
IN
OUTPUT
L
LL
RR
RL
(MONO)
R
MAIN(STEREO) MONITORAUX IN
POWERED MIXER
FOOT SW
MICLo-Z
Hi-Z
LINE
EFFECT
OUT
INPUT TO MAIN
DIGITAL
EFFECT
MAIN STEREO
MASTER
POWER
AMP
EFFECT RTNEFFECT OUT
010
010
LR
010
–15 +15
–15 +15
–15 +15
AUX IN TAPE IN
125 250 500 1k 2k 4k 8k
125 250 500 1k 2k 4k 8k
LR
(MONO)
67
67
MONI
BAL/PAN
EFFECT
MIC
LINELR
(MONO)
8
8
Lo-Z
Hi-Z
5
5
Lo-Z
Hi-Z
4
4
Lo-Z
Hi-Z
3
3
Lo-Z
Hi-Z
2
2
Lo-Z
Hi-Z
1
1
–12
+12
•
6
•
0
•
6
•
–12
+12
•
6
•
0
•
6
•
–12
+12
•
6
•
0
•
6
•
–12
+12
010
010
010
HIGH
MID
LOW
LEVEL
010
LR
–15 +15
–15 +15
–15 +15
010
010
LEVEL
LOW
PAD
MONI
PAN
EFFECT
MID
HIGH
010
LR
–15 +15
–15 +15
–15 +15
010
010
LEVEL
LOW
PAD
MONI
PAN
EFFECT
MID
HIGH
010
LR
–15 +15
–15 +15
–15 +15
010
010
LEVEL
LOW
PAD
MONI
PAN
EFFECT
MID
HIGH
010
LR
–15 +15
–15 +15
–15 +15
010
010
LEVEL
LOW
PAD
MONI
PAN
EFFECT
MID
HIGH
010
LR
–15 +15
–15 +15
–15 +15
010
010
LEVEL
LOW
PAD
MONI
PAN
EFFECT
MID
HIGH
010
LR
–15 +15
–15 +15
–15 +15
010
010
LEVEL
LOW
PAD
MONI
PAN
EFFECT
MID
HIGH
010
LR
010
–15 +15
–15 +15
–15 +15
MONI
BAL/PAN
EFFECT
010
HIGH
MID
LOW
LEVEL
010010010
010
Main Speakers
Microphone
L+R
BRIDGE
STEREO
Monitor Speakers
Guitar
Bass Guitar
Direct
Box
Guiter Effect
Processor
Effect Processor
Synthesizer
88
Note: Set the power amp select switch of the
POWER AMP section to the “MAIN MONI-
TOR” position.
If you are using an external effect, we recom-
mend that you turn down the EFFECT RTN
controls of the MAIN and MONITOR sections.
If the external effect has a stereo output, it is
possible to connect its output jacks to the LINE
jacks of channels 5–6. However in this case, be
sure that the EFFECT controls are turned all the
way down for the channels into which the effect
sound is being input. If the EFFECT controls
are raised, feedback will occur, and your speak-
ers may be damaged.