Filter
Top Products
The indicator of the effect module currently selected for
editing is flashing.
With each push of the MODULE SELECT key, the
edited module moves one position to the right. When the
REV/DLY module is reached, the cursor loops back to
the COMP&WAH module.
3.Next, use the PARAM SELECT ▼ key to select the
parameter within that module that you wish to edit.
The indicator of the selected parameter is flashing.
With each push of the PARAM SELECT key, the selected
parameter moves one position down. When PARAM 4 is
reached, the cursor loops back to PARAM 1.
The value of the selected effect parameter is shown on
the display. If the display shows only "
--", the effect
module is OFF. Set the effect module to ON before
editing, as described on page 8.
4.Use the VALUE +/- keys to change the parameter
value.
For details on the parameters of each effect module,
please refer to "Effect Types and Parameters" on pages 9
– 12.
Parameter setting changes made in this way are only
temporary. If you return to the Play mode or select a
different patch without storing the new settings first, the
settings will be lost.
For details on how to store a patch, please refer to the
explanation at right.
In the Edit mode, effect modules can be turned on and off
independently.
1.Pressing a pedal corresponding to an effect module
that is currently on (module cursor indicator lit) turns
the effect module off. The indicator goes out.
2.Press the pedal again to turn the effect module back
on.
The EQ module cannot be switched off. To disable this
module, set all parameters (PARAM 1 through PARAM
4) to the value "5".
The pedals 1 – 3 and the BANK pedal correspond to the
following effect modules:
• BANK pedal: COMP&WAH
• Pedal 1: DISTORTION
• Pedal 2: CHO/FLG
• Pedal 3: REV/DLY
The effect module ON/OFF setting can also be stored as
part of a patch.
If an edited patch is not stored, the change will be lost when
another patch is selected. To preserve a setting, store the
patch as described below.
1.Press the STORE key in the Edit mode.
This activates the store standby condition.
Storing is possible also in the Play mode.
2.Choose the bank and patch number in which you want
to store the patch.
Use the BANK pedal to first select the bank and then
specify the patch number with the pedals 1 – 3.
Patches cannot be stored in the PRESET group. If a
patch was chosen from the PRESET group, the store
destination will automatically become the USER group.
Specify a bank and patch number in the USER group.
3.If no bank and patch number is specified for a patch
selected from the USER group, the patch will be stored
in the original location.
If no bank and patch number is specified for a patch
selected from the PRESET group, the patch will be stored
in "A1" of the USER group.
When a patch is stored, the patch that was previously
stored in that number will be overwritten (erased). Take
care not to erase a patch that you want to keep. When
wishing to restore all factory preset patches, please refer
to "Reinitializing the 1010 (Special Mode)" on page 13.
Restoring individual patches is not possible.
4.Press the STORE key again. The patch is stored, and
the 1010 reverts to the Play mode.
If the STORE key has not yet been pressed for the second
time, you can use the EDIT key to cancel the store
process and return to the Play mode.
NOTE
HINTHINT
NOTE
HINTHINT
Storing a Patch
HINTHINT
NOTE
Switching Effect Modules On and Off
NOTE
HINTHINT
HINTHINT
PARM
PARM
1
PARM
1
2
PARM
3
PARM
4
PARM
PARM
PARM
PARM
PARM
NOTE
MODULE MODULE MODULE MODULE MODULEMODULE
COMP
WAH
COMP
WAH
DIST EQ
CHO
FLG
REVERB
DELAY
NOTE
8
▲