1
TROUBLESHOOTING
Before requesting service for this unit, check the table below for a possible cause of the problem you are experiencing.
Some simple checks or a minor adjustment on your part may eliminate the problem and restore proper operation.
Symptom Remedy
POWER
he power does not turn on
• Check that the AC power cord is connected securel
• Remote Control batteries may be weak, replace them with new ones.
Leave the unit unplugged for 20-30 min, plug the unit back in. If the unit
does not power on please contact our customer service center for service
on the model
he unit turns on automatically
without an
operation
• The unit turns on automatically 2 seconds before the timer recording.
Language” menu appears every time
the power turns on
• The unit may not have been turned off correctly. Finish up the language setting
procedure by selecting a language in
anguage
menu. Press
[OK]
to activate the
setting, t
en press
[STANDBY/ON
to turn t
e unit to t
e stan
y mo
e.
Do not disconnect the AC power cord before placing the unit in the standby mode
GENERAL
The unit does not response
• “ ” or error message appears if the operation is prohibited
• Remote Contro
atteries may
e wea
, rep
ace t
em wit
new ones.
Leave the unit unplugged
or 20-30 min, plug the unit back in. I
the unit
does not power on please contact our customer service center
or service
on the model
No picture, sound or menu appears on
h
r
n
• Depending on the Source/Connection, confirm the following
-For Antenna/Basic Ca
e, re
o an Auto Scan on t
e mo
e
.
-For Sate
ite Receiver/Ca
e Box, c
ec
t
e connections to ma
e sure
ey are secure
y connecte
-For RF Coaxial Cable, redo an Auto Scan on the model
-For RCA Audio/Video, check the connections to make sure the
are
ecurel
connected
• Check if the connections are made securely and correctly.
• Check if the cables are dama
ed.
Check i
a correct external input channel is selected on
our TV. (Re
er to page 22.
• Check i
you have completed the channel setting. (Re
er to pages 29-31.
• While the setup menu or timer programming display is shown, or while the
screen saver is active
the audio is muted.
Clock setting and channel setting
cannot be
erformed
• If a recording is in progress, these operations cannot be performed
Time jumps/Auto Clock set’s incorrect
time
• Set the “Auto Clock Setting” to “OFF” on page 104 and try “Manual Cloc
Setting” on page 34
T
e unit
oes not operate proper
y
Moisture
as con
ense
insi
e t
e unit. Remove t
e
isc an
eave t
e unit
turned on
or about 2 hours until the moisture evaporates. (Re
er to page 3.)
“Repairin
” appears on the TV screen
Repairing
• I
there is a power
ailure or unplugging during recording,
inalizing,
ormatting or editing (even a
ter “Repairing” disappears), a repairing
process will begin automatically just a
ter turning the unit on again.
It may take several minutes up to several hours
In case you intend to cancel the
repa
r
ng process
Repairing
Do you want to cancel a repairing
process? When selecting “Yes”,
the disc may not be usable.
Yes
No
• I
you intend to cancel the repairing process, press
OPEN/CLOSE
on the
ront panel, then select “Yes” and press [OK]. A
ter that, press
OPEN/CLOSE
to take out the
isc. The disc cancelled during the
repairing process MAY NOT work
T
e c
oc
isp
ay
oes not appear in
the front panel display
• C
ec
t
at t
e AC power cor
is connecte
secure
y
• (In case of power failure) Check the breaker and clock settin
hen you forget the password for
arental lock.
• Please cancel the password and the set level. (Refer to pa
e 106.
No analo
TV closed captions are
out
ut
• If you are using HDMI connection to watch the TV programs through
this unit, analog TV closed caption cannot be output. Try using another
out
ut connection to the TV
Instructions continue on the next pa
e.
