Filter
Top Products
accomidate the use of some older European xtures.
33. DMX XLR Output: A maximum of 96 DMX channel output. This is
the DMX signal output. This is a 3 pin XLR connector. If connecting to
a 5 pin XLR input connector you must use a 3-5 pin adaptor.
34. Midi Thru: This connection is used to connect the incoming MIDI
signal to another MIDI device.
35. Midi In: This connection is used to connect a MIDI triggering device,
such as a keyboard or drum machine.
36. Audio Line Input: Signal input range from 100mV to 1Vpp. This is an
audio line input. Connect a mixer or other audio device to trigger this
unit to sound. When an audio signal is connected it will automatically
disconnect the unit’s internal microphone.
37. Foot Control Input: This connection is for the optional external Foot
Controller.
Foot Controller Pin Conguration:
1. Step Up
2. Pattern Up
3. Stand By
4. Full On
5. Common
Operating Instructions
Programming Scenes (Steps) into Chase Patterns: This
function allows you to turn on specic channels (1-16) at one time to
be programmed into a Chase. This controller stores 60 CHASE PAT-
TERNS, 1-30 are user programmable and 31-60 are preset and cannot be
changed. You may program SCENES into CHASE PATTERNS 1-30 only.
To program a scene:
1. Press and hold down the PROGRAM BUTTON (23) for two
seconds. The green program LED will turn on indicating you are in
program mode.
2. At this point the display should read 01:01. The rst two digits display
the CHASE bank and the second pair of digits displays the SCENE
bank.
3. Use these PATTERN BUTTONS (18 & 19) to select a CHASE bank
to store the scenes you are about to create.
4. Once you have selected a CHASE bank, you may begin to adjust
the channels (1-16) to your liking.
5. Once you have adjusted the channels to your desired settings press
the PROGRAM BUTTON (23) once to record your scene into
memory. When you press the PROGRAM BUTTON (23), all the
channel LED’s will ash indicating the scene has been stored into
memory. The right two digits in the LCD DISPLAY (6) will advance
to the next available step.
6. You may continue this pattern up to 99 times per each CHASE
PATTERN. You may mix and match the top and bottom channel
buttons together in a CHASE PATTERN, however, remember that
the upper and lower channels chase speeds are controlled
separately.
7. When you have completed programming all your steps you must
record an “End Step” to nalize your CHASE PATTERN. To
program the “End Step,” press and hold down the SHIFT BUTTON
(16). While holding down the SHIFT BUTTON (16), press and
release the PROGRAM BUTTON (23). You will see all the LEDs
ash indicating the “End Step” was successfully programmed.
8. To exit the program mode, press and hold the PROGRAM
BUTTON for two (2) seconds.
Running Chase Patterns: This function allows you to automati-
cally run one of the 60 CHASE PATTERNS. The speed of these chase’s
can be controlled by the DIMMER SPEED (9) and SWITCH SPEED (10)
faders. The DIMMER SPEED (9) will control channels 1-8 and SWITCH
SPEED will control channels 9-16. To run a chase pattern:
1. Press the CHASE BUTTON (24). The chase LED in the LCD Display
(6) will light indicating you are in CHASE MODE.
2. Use the PATTERN BUTTONS (18 & 19) to select the CHASE PAT-
TERN you wish to run.
3. Use the SPEED CONTROLS (9 & 10) to adjust your chase speed
and the LEVEL CONTROL (8) to set your output intensity.
Using the Built In Programs: This controller comes with 30
preset programs. These programs are designed to get you up and running
in minutes. Programs 31-40 control channels 1-8, 41-50 control channels
9-16, and programs 51-60 combine channels 1-16. Chase Pattern 40 is a
combination of 31-39. Chase Pattern 50 is a combination of 41-49. Chase
Pattern 60 is a combination of 51-59. These chases can not be changed
or edited.
©American DJ Suply® www-americandj.com Light Stantion Instruction Manual Page 9 ©American DJ Suply® www-americandj.com Light Stantion Instruction Manual Page 10