Filter
Top Products
Cross Mode: Cross mode is a manual adjustment that fades from one
step to the next. You may use this function in any CHASE PATTERN. This
function will not effect channels 9-16. To use this function:
1. Be sure you are in CHASE MODE.
2. Turn CROSS MODE on by holding down the SHIFT BUTTON (16),
and pressing the CROSS SETUP BUTTON (20) until the yellow
CROSS ON LED glows.
3. Press the CROSS BUTTON (15) to activate the cross function.
Channels 1-8 will stop chasing and the MASTER FADER (4) LED
will turn off. Either the “A” or “B” LED on the MASTER FADER
(4) will begin to glow depending on the position of the fader.
4. You may now use the MASTER FADER (4) to manually cross fade
through a CHASE PATTERN’s steps. Sliding the MASTER FADER
(4) up and down will change the steps from one to the next. The
slower you move the fader the slower the scenes will fade from one
to the next.
5. In this operation, the FADE TIME (7) level will function.
6. You may use the CHASE PATTERN BUTTONS (18 & 19) to select a
different chase at any time.
Loop Mode: This function allows you to group several CHASES
together and run them in a sequential repeating pattern.
1. Be sure you are in CHASE MODE.
2. Go to the rst pattern you wish to program into the loop and press
the LOOP BUTTON (22). After you press the LOOP BUTTON (22),
the channel green LEDs will ash and “LP” will be displayed in
the right two (2) digits in the LCD DISPLAY (6).
3. Repeat step two until you have enter all your desired CHASE
PATTERNS. If the LOOP BUTTON (22) is not pressed within 10
seconds, the loop will automatically start to cycle. You may add the
same CHASE PATTERN more than once.
4. When you have nished entering all you chases, wait 10
seconds and “CL” will appear in the right two digits of the LCD
DISPLAY (6). When this happens the chases will automatically
begin to run and loop in the same pattern you programmed them in.
5. To cancel or exit this mode, press the LOOP EXIT BUTTON
(22) while holding down the SHIFT BUTTON (16).
Show Mode: This function gives you manual control over channels
1-8 when running in normal chase mode. This function will not effect
channels 9-16 in any way. To operate in show mode:
1. Run a chase in a normal fashion.
2. Bring the DIMMER SPEED SLIDER (9) down until “SHO” appears
in the LCD DISPLAY (6).
3. When “SHO” appears you may use the STEP UP and DOWN
BUTTONS (20 &21) to manually step through a CHASE PATTERNS.
4. In this function you may change your selected CHASE PATTERN
at any time.
Deleting Chases: This function allows you to delete an unwanted
CHASE PATTERN. Please note that only CHASE PATTERNS 1-30 can be
deleted, 31-60 are built in programs and can not be deleted or changed in
any way. Also note that a program is never completely erased unless you
initialize the controller. The program will simply not be able to be executed.
It can always be recalled later. To delete a CHASE PATTERN:
1 .Enter PROGRAM MODE as described in “Programming Scenes”
on page 9.
2. Use the PATTERN BUTTONS (18&19) to select the pattern you wish
to delete.
3. When you reach the program you wish to delete, press the DELETE
PROGRAM BUTTON (25) while holding down the SHIFT BUTTON
(16). All the channel LED’s will ash indicating the command
registered.
4. To exit this function press the CHASE BUTTON (24).
Assign Add/Kill: This function allows you to override a chase and turn
a single or a group of channels on. Channels are assigned to the FLASH
BUTTON (1 & 13), allowing to have a total of 16 programmed overrides.
You may use your overrides at different times and may use more than one
at a time. You can set this function to blackout (“KILL”) the chase, so only
your override channels come on. You may also, set this function to “ADD”
to the chase. When you “ADD,” your override channels will come on as
your chase is running. This function will operate in any chase. This will
be a momentarily function and your chase return to normal as soon as
release the FLASH BUTTON (1 & 13).
To program in an override:
1.Hold down the ASSIGN BUTTON (25) for two seconds until the
red assign LED come on and “AS” is displayed in the LCD
Display (6).
2. While holding down the SHIFT BUTTON (16), use the PATTERN UP
BUTTON (18) to selected “ASSIGN ADD.” ASSIGN ADD will be
indicated by a red LED above the PATTERN UP BUTTON (18).
©American DJ Suply® www-americandj.com Light Stantion Instruction Manual Page 11 ©American DJ Suply® www-americandj.com Light Stantion Instruction Manual Page 12