Filter
Top Products
3. Turn on any channels you wish to assign to a FLASH BANK.
4. After you have turned on your desired channels, press on of the
FLASH BUTTONS (1 &13) while holding down the ASSIGN
BUTTON (25). ALL the channel LED will ash indicating that your
program was placed into that FLASH BUTTON’s memory.
Recalling an ASSIGN PATTERN:
1. You may recall your assign pattern in any chase function.
2.To add to the chase be sure the yellow LED next to the ADD/KILL
(17) is off and the red ASSIGN ADD LED is on. Simply press the
FLASH BUTTON (1 & 13) that stores the scene you wish to recall.
You’ll notice that the chase remains running and your scene turns
on. You may recall (ADD) several scenes at once, by pressing as
many FLASH BUTTON (1 & 13) as you like at one time.
3. To blackout (KILL) the chase and just turn on your programmed
scene, press the ADD/KILL BUTTON (17) to turn on the yellow LED.
Be sure you are in ASSIGN KILL mode. Press the FLASH BUTTON
(1 & 13) that store the scene you wish to recall. You’ll notice that the
chase stops and your scene comes on.
4. For both “ADD” and “KILL” the scene will remain on as long as
hold the FLASH BUTTON (1 & 13) down. Also you may turn several
ASSIGNS on at once.
Blind Function: This functions allow you to blackout (BLIND) specic
channels from your chase programs. To BLIND a channel be sure you are
in chase mode and:
1. While holding down the SHIFT BUTTON (16) press and release the
BLIND BUTTON (21) to activate the blind function.
2. While holding down the SHIFT BUTTON (16) press and release the
FLASH BUTTON (1 & 13) that corresponds to channel you wish to
remove from the chase.
3. You may repeat this process to blind as may channels as you like.
4. To remove a channel simply reverse the process, hold down the
SHIFT BUTTON (16) and press and release the FLASH BUTTON (1
& 13) that correspond to channel you wish to return to the chase.
5. To cancel the BLIND FUNCTION hold down the SHIFT BUTTON
(16), press and release the BLIND BUTTON (21). This will disable
the blind function.
Patch Settings: This function allows you to overlap DMX channels
together, giving you up to 96 DMX channels to work with. This function
is useful if you would like several channels on one DMX pack to turn at
once. For example, say you have a 4 channel DMX pack with 5 amps
maximum load per a channel and you want to turn on four 500 watt
lamps on DMX channel one. Your DMX pack is automatically going to
assign one 4 DMX channels to your pack one for one. To reduce the
risk of constantly blowing your pack you can plug each lamp into all
four (4) of your packs channels. Then you can patch these channels
to be triggered all at once. Since each of the 16 channels of the Light
Station™ represent a DMX channel you would only have 16 to work
with. However, if you patch your DMX channels, you could have a
maximum of six DMX channels triggered per a channel on the controller.
So, you could tell your controller to trigger DMX channels 1-4 by slider
1 on the board. This would then activate all four channels on your
DMX pack, allowing all four lamps to be turned on at once, therefore
eliminating the possibility of blowing you pack channels due to excessive
load per a channel, because now your lamps are spread out through
your pack. To patch channels:
1.Press and hold down the PATCH BUTTON (27) until the red
indicator LED turns on.
2.The LCD DISPLAY (6) will read “01:01.” The left two digits
represent the controllers 16 channels (1-8 faders and 9-16 Latch
Buttons). The right two digits represent the 96 available DMX
channels.
3. Use the STEP up and DOWN BUTTONS (20 & 21) to adjust the
DMX channels you wish to patch.
4. Use the PATTERN UP and DOWN BUTTONS (18 & 19) to select
the controller channel (1-16) you wish to patch the DMX channel
too.
5. Be sure to select your DMX channel before you select your
controller channel to complete this function properly.
6. After you have completed your adjustments, hold down the PATCH
BUTTON (27) until the red indicator LED shuts off, to exit this
function.
Manual Mode: This function shuts off all other functions and allow
you to use the controller as a basic on/off dimmer. To activate this mode
press and release the MANUAL BUTTON (28) while holding down the
SHIFT BUTTON (16).
Manual Step Mode: This mode allows you to manually control chan-
nels 1-8 when in chase mode. This function will only effect channels 1-8,
channels 9-16 will continue to chase normally. In this function you can
©American DJ Suply® www-americandj.com Light Stantion Instruction Manual Page 13 ©American DJ Suply® www-americandj.com Light Stantion Instruction Manual Page 14