Filter
Top Products
2
Before use
Part names and
Functions
Connections
Basic
operations
Effector
function
Fader
Start function
USB settings
Troubleshooting
IndeX
specifications
System diagram
Main features
1. Wide range of input and output terminals
The input and output terminals available on this unit are described
below.
Input
• CD 2
• PHONO 2
• Mic 1
• AUX1 1
• AUX2 1 /Effect 1 (combined use)
Output
• Master 2
• Booth 1 /Effect 1 (combined use)
Input/Output
• USB Audio Interface
Additionally, this unit is a 96kHz/32 bit DAC supported DJ full digital
mixer equipped with USB MIDI and terminal output MIDI interface.
2. Designed to achieve high sound quality
• The unit features a 96 kHz/32-bit floating digital signal processor
(DSP) and 32-bit digital-to-analog converter (DAC) (master output).
The unit delivers high quality sound that is faithful to the original
sound source.
• An electrolytic capacitor designed to enhance sound quality is
employed in the power supply unit. Additionally, film capacitors that
are designed to enhance sound quality and high-precision metal
film resistors are used to configure the audio signal processing
unit, resulting in superb quality sound.
• The unit is equipped with a microphone amplifier that features a
discrete transistor configuration and low equivalent input noise of
126 dB, and a PHONO amplifier that features a signal to noise ratio
of 89 dB.
3. Multiple Effects
Specific parameters for each of the 8 different effects can be linked
to the beats per minute (BPM) of every track passing through the
mixer. The effects processor offers its own set of controls such as,
Dry/Wet mix, Parameter Low/High pass filter, Cross Over filter, Beat
time adjustments, TAP, Manual and Auto BPM, Pre Efx Cueing and
ON/OFF.
4. USB audio and MIDI interfaces
• 8-channel (4 stereo channels) 96 kHz USB audio input/output
function
• DVS (Digital Vinyl System) compatible.
• Most of the panel operations can output MIDI.
• The MIDI clock signal is detected from the computer, and can be
automatically used as a BPM value.
• The unit incorporates an effect send/return function that allows
effects to be applied to audio output from this unit using effector
software on a computer, and then to re-input the audio into the
unit.
• A low latency ASIO driver is also included with the unit.
5. High-reliability design for professional use
• Isolator filters are incorporated for each input channel.
• Crossfader slide torque can be adjusted to personal preferences.
• Matrix source selectors enable the selection of any of 6 input
sources
6. Others
• Ducking function reduces the amount of background sound during
mic usage.
• Channel Fader and Crossfader start function
• Auto Standby function (Eco mode)
Cautions on handling
• Before turning the power switch on
Check once again that all connections are correct and that there are
no problems with the connection cables.
• Power is supplied to some of the circuitry even when the unit is
set to the standby mode. When going on vacation or leaving home
for long periods of time, be sure to unplug the power cord from the
power outlet.
• About Condensation
If there is a major difference in temperature between the inside of
the unit and the surroundings, condensation (dew) may form on
the operating parts inside the unit, causing the unit not to operate
properly.
If this happens, let the unit sit for an hour or two with the power
turned off and wait until there is little difference in temperature
before using the unit.
• Cautions on using mobile phones
Using a mobile phone near this unit may result in noise. If that
occurs, move the mobile phone away from this unit when it is in use.
• Moving the unit
Turn off the power and unplug the power cord from the power
outlet. Next, disconnect the connection cables to other system units
before moving the unit.
• About Care
• Wipe the cabinet and control panel clean with a soft cloth.
• Follow the instructions when using a chemical cleaner.
• Benzene, paint thinner or other organic solvents as well as
insecticide may cause material changes and discoloration if brought
into contact with the unit, and should therefore not be used.