Filter
Top Products
TK-260G/270G
11
8-2. Channel Setting Mode
This is a mode for making channel settings with the panel
keys without using the FPU.
Pressing [MON] when "SELF" is displayed, sets Channel
Setting Mode.
Select an item set using [3] then change the selection with
the encoder.
The data displayed using [2] is stored in the memory and
then proceeds to the next item. Pressing [3] proceeds to
the next item without storing it in the memory.
Press [MON] to set the display to "SELF" and return to reset
(default) status.
Fig. 3
REALIGNMENT
8. Self Programming Mode (TK-270G only)
Write mode for frequency data and signalling etc. Mainly
used by the person maintaining the user equipment.
8.1 Self programming mode setting
Remove D17 from the TX-RX unit (Figure 3) (K models
only). Hold down the [LAMP]+[●] switches and turn the
power switch on.
When the self programming mode is entered, [SELF]
appears on the display. The mode changes automatically
to Model Select Mode and "PORTABLE" is displayed in
about one second.
Note :
This mode (self programming mode) cannot be set when it
has been disabled with the FPU.
No. Function Choices Display Remarks
Select
1-128
_1-_1._
[3] : Group selection/
Channel
_1-128._
Channel selection change
Select
1-128
_1.-_1_
Group
128.-_1_
1
RX frequency
Step 2.5kHz-1MHz
STP_250
Display when an item is selected
STP_1000
or when a step is changed
(about 0.5 seconds)
[
•
] Step change
VHF : 2.5, 5.0,6.25,7.5kHz,1MHz,Step
Blank ————
[LAMP] : Freq On/Blank switching
100.0000-
R.100.0000
The rightmost dot indicates
550.0000MHz 50Hz digit (On=5; Off=0).
2
Rx Signaling
OFF ————
[LAMP] : Off/QT/DQT switching
QT 67.0-250.3Hz
QT_67.0_
[
•
] : Mode switching
(EIA Mode)
QT_250.3_
[
°
] : Normal/Inverse
QT 67.0-250.3Hz
QT_67.0*
switching
(0.1Hz Step Mode)
QT_250.3*
DQT 000-777 (Normal)
DQT000N*
(1 Step Mode)
DQT777N*
DQT 023-754 (Normal)
DQT023N
(Standard Table Mode)
DQT754N
DQT 000-777 (Inverse)
DQT000I*
(1 Step Mode)
DQT777I*
DQT 023-754 (Inverse)
DQT023I
(Standard Table Mode)
DQT754I
D17
X57-587X
Compoent Side
Radio type Portable Mobile
[MON]
Radio Band & Channel Type
Function set mode
Frequency Version
Self programming mode
[2]
[2]
[LAMP]
VHF 8CH
Channel set mode
[2]
[3]
VHF 128CH UHF 8CH UHF 128CH
[CH][CH]
[CH]
[CH]
[CH]
VHF F1
VHF F2 UHF F1 UHF F3
[CH][CH]
[CH]
UHF F4
[CH]
[CH]
Cannot be
set when
Portable is
select
Cannot be
set when
Mobile is
select
●
Flow Chart
Note :
IF the radio type of TK-270G was temporally set to "Mobile"
for the cloning purposes, "UNPROG" is displayed (at User
Mode) when the TK-270G is turned on.
In this case, please set the radio type back to "Portable" at
Model Select Mode menu.