Filter
Top Products
14
15
Footswitch
1
2
3
4
CABLE CONNECTOR
This 7-pin DIN connector is provided for connecting the footswitch to the amplier RE-
MOTE SWITCH (20) via the cable included in the carton. Connections at the switch and
the amplier should be made before the amp is powered up.
LEAD/RHYTHM SELECTOR
This switch selects between the Rhythm and Lead channels on the amplier. The adja-
cent LED will illuminate when the Lead/Lead channel is selected. When the LED is dark,
the Rhythm/Rhythm channel is selected. The CLEAN SELECTOR (32) must be in the
BYPASS mode to activate either the Rhythm or Lead channel.
CLEAN SELECTOR
This switch selects the Clean channel and will activate regardless of the position of the
Lead/Rhythm SELECTOR (31). The adjacent LED will illuminate when the Clean chan-
nel is selected. This switch must be in the BYPASS position, indicated by a dark LED, in
order to utilize the Lead/Rhythm SELECTOR (31).
EFFECTS SELECTOR
This switch activates the amplier’s effects loop. The adjacent LED will illuminate when
the effects loop is active.
Lead/RhythM ByPass ByPass
Lead Clean Effects
1
2 3 4
POWER AMPLIFIER SECTION:
Tubes:
Four EL34's with 12AX7 driver
Rated Power and Load:
120 W RMS into 16, 8, or 4 ohms
Power @ Clipping:
(Typically @ 5% THD, 1 kHz, 120 VAC line)
120 W RMS into 16, 8, or 4 ohms
Frequency Response:
±3 dB 50 Hz to 20 kHz @ 90 W RMS into 8 ohms
Hum and Noise:
Greater than 76 dB below rated power
Power Consumption:
Domestic: 400 W, 50/60 Hz, 120 VAC
Export: 400 W, 60 Hz, 220-230/240 VAC
PREAMP SECTION:
Tubes:
Three 12AX7
The following specs are measured @ 1 kHz with the controls preset
as follows:
Low and High EQ @ 10, Mid EQ @ 0
Rhythm and Lead Posts @ 10
Bass, Middle and Treble EQ @ 5
Effects Send @ 0
Effects Return @ 10
Master Level @ 5
Nominal Levels are with Pre Gain @ 5
Minimum Levels are with Pre Gain @ 10
Clean Channel:
Nominal Input Level: -20 dBV, 100 mV RMS
Minimum Input Level: -30 dBV, 30 mV RMS
Maximum Input Level: 0 dBV, 1.0 mV RMS
Rhythm Channel:
Nominal Input Level: -80 dBV, 0.1 mV RMS
Minimum Input Level: -90 dBV, 0.03 mV RMS
Lead Channel:
Nominal Input Level: -80 dBV, 0.1 mV RMS
Minimum Input Level: -90 dBV, 0.03 mV RMS
Effects Send:
Load Impedance: 47 k ohms or greater
Minimum Output: -10 dBV, 300 mV RMS
Maximum Output: 0 dBV, 1 V RMS
Effects Return:
Impedance: High-Z, 80 k ohms
Minimum Input Sensitivity: -10 dBV, 300 mV RMS
Maximum Input Sensitivity: 0 dBV, 1 V RMS
Line Output:
Load Impedance: 47 k ohms or greater
Adjustable Output: ±20 dBV, 0.1 V RMS-10 V RMS
REMOTE FOOTSWITCH:
Special 3-button unit with LED indicators (supplied)
System Hum and Noise @ Nominal Level:
(Clean channel, 20 Hz to 20 kHz unweighted)
Greater than 74 dB below rated power
(Special noise gate circuitry for Lead & Rhythm)
Equalization: (Clean channel only)
Custom Low, Mid, and High passive type EQ
Voicing: (Rhythm and Lead channels only)
Active Bass, Middle, and Treble EQ
Boost/Cut ±12 dB
Dimensions and Weight:
11.0" (279 mm) H x 26.5" (673 mm) W x 11.0" (279 mm) D
52 lbs. (23.6 kg)
Specifications