Filter
Top Products
9
How to Control the Display from the SRP-X700P
You can connect the following projectors and displays to the SRP-X700P.
For setting the projectors and displays, refer to the “REMOTE Screen” described on page 14 of the Control Software Manual.
Note
Models other than those above may be supported. For details, please contact your local Sony Sales office or Dealer.
List of the supported models shown above is as of April 1st, 2002.
Maximum RS-232C cable length is 15 m or less.
PROJECTOR CONTROL RS-232C Terminal
To connect the RS-232C terminal of applicable projectors and that of plasma display to this terminal;
This model can switch the input signals and power ON/STANDBY of the projector and plasma display in interlocked condition.
X700P side
5BNC
output terminal
S-VIDEO
terminal
VIDEO
terminal
5BNC
output terminal
S-VIDEO
terminal
VIDEO
terminal
5BNC
output terminal
S-VIDEO
terminal
VIDEO
terminal
5BNC
output terminal
S-VIDEO
terminal
VIDEO
terminal
5BNC
output terminal
S-VIDEO
terminal
VIDEO
terminal
Input terminal of
connection destination
INPUT A 5BNC
terminal
VIDEO IN S-VIDEO
terminal
VIDEO IN VIDEO
terminal
INPUT1 RGB/YUV
terminal
INPUT2 RGB/YUV
terminal
VIDEO COMPOSITE IN
terminal
INPUT A
terminal
S-VIDEO
terminal
VIDEO
terminal
INPUT A
terminal
VIDEO IN S-VIDEO
terminal
VIDEO IN VIDEO
terminal
INPUT2 5BNC
terminal
INPUT3 S-VIDEO
terminal
INPUT3 VIDEO
terminal
X700P side
PROJECTOR
CONTROL
(RS-232C) terminal
PROJECTOR
CONTROL
(RS-232C) terminal
—————
—————
PROJECTOR
CONTROL
(RS-232C) terminal
Remote terminal of
Connection destination
RS-232C terminal
REMOTE terminal
—————
—————
CONTROL PORT
terminal
Control S terminal of
connection destination
—————
—————
CONTROL S/
PLUG IN POWER
terminal
CONTROL S IN/
PLUG IN POWER
terminal
—————
X700P side
—————
—————
CONTROL S
PROJECTOR OUT
terminal
CONTROL S
PROJECTOR OUT
terminal
—————
<SRP-X700P side>
(D-sub 9-pin, male)
<Sony projector/
plasma display side>
(Dub-sub 9-pin, female)
Video terminal RS-232C control CONTROL S control
Model
name
VPL-FX50
VPL-PX21
VPL-PX31
VPL-PX32
PFM-42B1
VPL-PX15
VPL-PX10
VPL-PS10
VPL-CX11
VPL-CX10
LP-XP45
LP-XP40
made by
Sanyo
Electric
PROJECTOR CONTROL CONTROL S IN/OUT Terminal
PROJECTOR
IN
OUT
<SRP-X700P>
CONTROL S
Remote
commander
Projector
The SRP-X700P can switch the input signals and power ON/STANDBY of
the projector automatically when CONTROL S cable is connected to Sony’s
projector as interlocked operation. The RGB signal and the component
signal cannot be connected at the same time for the interlocked operation.
Connect the wired remote commander supplied with a projector to the
CONTROL S IN terminal. Then you can establish various setups of a
projector from the SRP-X700P. If you want to use the wired remote
commander on battery, locally fabricate a connecting cord with STEREO
mini plug connected at one end, for supplying the power.
Pin No. Signal Function
1 FG Frame ground
2 RD Receive data
3 TD Send data
4 ER Data terminal ready
5 SG Signal line ground
6 DR Data set ready
7 RS Request to send
8 CS Clear to send
9 N. C Not connected
Pin No. Signal Function
1 FG Frame ground
2 RX DA Receive data
3 TX DA Send data
4 DTR Data terminal ready
5 GND Ground
6 DSR Data set ready
7 RTS Request to send
8 CTS Clear to send
9 RI Called display