Tascam CD-RW900SL Recording Equipment User Manual


 
IMPORTANT SAFETY PRECAUTIONS
20 TASCAM CD-RW900SL
4 − Playback operations
20 TASCAM CD-RW900SL
A to B repeat playback
If a specific portion between two points on the disc is spec-
ified, that portion can be played back repeatedly.
1. During playback, press the A-B key on the remote
control at the beginning of the desired portion on
the disc.
The REPEAT indicator lights up in the display and the
A- indicator will flash.
2. At the end of the desired portion on the disc, press
the A-B key again.
Then, the REPEAT and A-B indicators light up in the
display, and the desired A-B section will be played
back repeatedly.
NOTE
You can also operate this function during playback standby.
3. To cancel the A-B repeat mode and resume normal
playback, press the A-B key once again.
The REPEAT and A-B indicators will turn off.
NOTE
A-B repeat cannot be used when the specified A-B
section spans more than one track, and cannot be
used with MP3 discs.
When the STOP key is pressed, the specified A-B
section is cancelled.
Using the auto cue function, you can select a cue point
where sound begins (not where a track begins) within a
track.
Turn the auto cue function on and use the A_CUE LEVEL
sub-menu option (see “Operation basics” on page 15) to set
the sound detection level (-24, -30, -36, -42, -48, -54, -60,
-66 and -72 dB).
Then, select a track and press the PLAY key. The unit
enters playback ready mode.
When the PLAY key is pressed again, playback begins at
exactly the cue point.
While the auto function is on, the A.CUE indicator lights up
on the display.
Auto Cue function
This function allows the playing back a single track, and
the automatic cuing of the next track ready for playback.
Use the A_READY sub-menu option to turn the function
on or off. When on, the A.READY indicator lights up on the
display.
Combined with Auto Cue function, the unit enters play-
back ready mode at the point where the sound detection
level is set in A_CUE LEVEL sub-menu option of the next
track.
Auto Ready function
Pitch control function
When playing back an audio CD, the pitch (or speed) of the
playback can be varied. Pitch can be varied +/- 16%.
1. When stopped, press the PITCH key on the remote
control to turn on the Pitch control function.
Or, use the PITCH option in the PLAY sub-menu
(refer to “Operation basics” on page 15).
The current pitch value appears on the display for
seconds and the PITCH indicator will light up.
2. Press the MENU key and select the PITCH CONT
option in the PLAY sub-menu to set the desired
value and push the MULTI JOG dial to enter.
Pitch>XXX will appear on the display.
Then, rotate the MULTI JOG dial to set the desired value.
NOTE
Use the PITCH STEP option in the PLAY sub-menu to
adjust the pitch value steps from 0.1% to 1.0% in 0.1%
increments (default: 0.1%).
3. Press the MENU key or push the MULTI JOG dial to
enter and return to normal mode.
During playback, the pitch control playback can
be disabled temporarily. Press the PITCH key on
the remote control or use the PITCH option in the
PLAY sub-menu to turn the function off.
Pitch>OFF appears on the display and the pitch
control playback will be off temporarily, until the
function is re-set again.
To resume the pitch control playback, press the
PITCH key again or use the PITCH option.
NOTE
When turning the pitch control on and off during
playback, sound output is cut for a short instant.
Pitch control cannot be used with MP3 discs.