Filter
Top Products
©American DJ Supply® - www.americandj.com - DJ Scan/RG™ Instruction Manual Page 4©American DJ Supply® - www.americandj.com - DJ Scan/RG™ Instruction Manual Page 3
DJ Scan/RG™ Quick Start
The DJ Scan/RG™ features a bright 150 watt/500 hour lamp life
halogen bulb with a separate gobo and color wheel. The color wheel
features seven brilliant colors plus white and the gobo wheel features
6 gobos plus a large and small spot. This fixture incorporates the use
of high quality stepper motors for a more accurate mirror movement.
Mirror movement allows for a full 90 degree tilt (vertical) and a 45
degree pan (horizontal). An internal built in microphone allows the
fixtures to run in Stand Alone mode so there is no need for an external
controller. The DJ Scan/RG™ may also be set-up to run in a Master-
Slave mode when used in multiples, up to four units. When used in the
Master-Slave mode, the unit will chase to several internal programs.
The DJ Scan/RG™ can also be controlled via a standard DMX control-
ler such as the American DJ
® Show Designer,™ or the American
DJ
® DMX Operator,™ giving the user independent control over the
gobo and color wheel as well as the mirrors pan and tilt movements.
Note: The built in programs in the DJ Scan/RG™ are so good you may
never need a DMX controller.
• ZB-JCR/H5 15V/150W, 500 Hour Lamp.
• DMX-512 Compatible.
• Stepper motors for smooth movements.
• 7 colors plus white.
• 7 Gobos plus spot.
• 4 Rotating Gobos, 4 Fixed Gobos.
• 4 Replaceable Gobos (26mm diameter - 22mm viewable)
• Master/Slave Operation
• Sound Active.
• Optional MINI/C controller, for blackout control.
DJ Scan/RG™ Features
Master/Slave Quick Start Stand Alone Mode
Connect up to four units together via XLR cables. The master unit
will run the slaves to the masters built in programs and internal
microphone. Plug in all units. When the DJ Scan/RG™ is first turned
on, it will run through an internal self test where it resets all motors to
their zero position. After the self test the units will react to sound, and
chase to the several built in programs.
• Do not spill water or other liquids into or on to your unit.
• Be sure that the local power outlet match that of the required voltage
for your unit.
• Do not attempt to operate this unit if the power cord has been frayed
or broken. Please route your power cord out of the way of foot traffi c.
• Do not attempt to remove or break off the ground prong from
the electrical cord. This prong is used to reduce the risk of electrical
shock and fi re in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the top cover under any conditions. There are no
user serviceable parts inside.
• Never plug this unit in to a dimmer pack
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged in any way.
• Never operate this unit when it’s cover is removed.
• To reduce the risk of electrical shock or fi re, do not expose this unit
rain or moisture
• This unit is intended for indoor use only, use of this product outdoors
voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power Cord Protection - Power cords should be routed so they are
not likely to be walked on or pinched by items placed upon or against
them, paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the unit.
• Cleaning -The fixture should be cleaned only as recommended by
the manufacturer.
• Heat -The unit should be situated away from heat sources such
as radiators, heat registers, stoves, or other appliances (including
amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The fixture does not appear to operate normally or exhibits a
marked change in performance.
DJ Scan/RG™ Safety Precautions