Casio PX-3 Electronic Keyboard User Manual


 
Appendix
E-61
English
Single-effect Algorithms
01: Equalizer
This is a three-band equalizer.
Parameter Value Ranges:
0 :Equalizer 1 Frequency (1.0, 1.3, 1.6, 2.0, 2.5, 3.2, 4.0, 5.0 [KHz])
Adjusts the center frequency of Equalizer 1.
1 :Equalizer 1 Gain (–12 to 0 to +12)
Adjusts the gain of Equalizer 1.
2 :Equalizer 2 Frequency (1.0, 1.3, 1.6, 2.0, 2.5, 3.2, 4.0, 5.0 [KHz])
Adjusts the center frequency of Equalizer 2.
3 :Equalizer 2 Gain (–12 to 0 to +12)
Adjusts the gain of Equalizer 2.
4 :Equalizer 3 Frequency (1.0, 1.3, 1.6, 2.0, 2.5, 3.2, 4.0, 5.0 [KHz])
Adjusts the center frequency of Equalizer 3.
5 :Equalizer 3 Gain (–12 to 0 to +12)
Adjusts the gain of Equalizer 3.
Note: The Gain value is not a dB value.
02: Compressor
Compresses the input signal, which can have the effect of
suppressing level variation and making it possible to sustain
dampened sounds longer.
Parameter Value Ranges:
0 :Depth (0 to 127)
Adjusts compression of the audio signal.
1 :Attack (0 to 127)
Adjusts the attack amount of the input signal. A smaller value
causes prompt compressor operation, which suppresses the
attack of the input signal. A larger values delays compressor
operation, which causes the attack of the input signal to be output
as-is.
2 :Release (0 to 127)
Adjusts the time from the point the input signal drops below a
certain level until the compression operation is stopped.
When an attack feeling is desired (no compression at the onset of
sound), set this parameter to as low a value as possible. To have
compression applied at all times, set a high value.
3 :Level (0 to 127)
Adjusts the output level.
Output volume changes in accordance with the Depth setting and
the characteristics of the input tone. Use this parameter to correct
for such changes.
03: Limiter
Limits the input signal level so it does not rise above a preset level.
Parameter Value Ranges:
0 :Limit (0 to 127)
Adjusts the volume level of the limit at which limiting is applied.
1 :Attack (0 to 127)
Adjusts the attack amount of the input signal.
2 :Release (0 to 127)
Adjusts the time from the point the input signal drops below a
certain level until the limit operation is stopped.
3 :Level (0 to 127)
Adjusts the output level.
Output volume changes in accordance with the Limit setting and
the characteristics of the input tone. Use this parameter to correct
for such changes.
04: Enhancer
Enhances the profiles of the low range and high range of the input
signal.
Parameter Value Ranges:
0 :Low Frequency (0 to 127)
Adjusts the low range enhancer frequency.
1 :Low Gain (0 to 127)
Adjusts the low range enhancer gain.
2 :High Frequency (0 to 127)
Adjusts the high range enhancer frequency.
3 :High Gain (0 to 127)
Adjusts the high range enhancer gain.
05: Chorus
This is a stereo chorus effect using a sine wave LFO.
Parameter Value Ranges:
0 :LFO Rate (0 to 127)
Adjusts the LFO rate.
1 :LFO Depth (0 to 127)
Adjusts the LFO depth.
2 :Feedback (–64 to 0 to +63)
Adjusts the strength of feedback
3 :Wet Level (0 to 127)
Adjusts the level of the effect sound.
4 :Polarity (–, +)
Reverses the LFO signal of one channel, which changes the
expanse of sound.
06: Tremolo
Adjusts the volume of the input signal using an LFO.
Parameter Value Ranges:
0 :Rate (0 to 127)
Adjusts the tremolo rate.
1 :Depth (0 to 127)
Adjusts the tremolo depth.
07: Early Reflection
Extracts the initial reflection sound from reverberation sound.
Parameter Value Ranges:
0 :Wet Level (0 to 127)
Adjusts the level of the effect sound.
1 :Feedback (0 to 127)
Adjusts the repeat of the reflected sound.
2 :Tone (0 to 127)
Adjusts the tone of the reflected sound.
DSP Algorithm List