Filter
Top Products
3
Getting Started Connections Basic Operations Specifi cations Troubleshooting
Effector Function Fader Start UtilityUSB
Part Names and Functions
For further details on the functions and other aspects of the parts, refer to the page numbers in
parenthesis.
Top Panel
R3
E0
W9
W8
W7
W6
W3
W4
W1
Q9
W0
Q8
Q7 Q6
E9R0
Q4
Q5
Q3
Q2
Q0
Q1
u
i
o
E8
r
y
E6
e
w
q
R2R1E5E2E3E1
E4
t
W2
W5
E7
q
MASTER LEVEL control
Adjusts the level of the MASTER outputs.
The LIMITER LED indicates the operating status
of the master output limiter.
• Limiter OFF: LED is off.
• Limiter ON: LED lights up green.
• While limiter is operating: LED lights up red.
w
Master EFX INS 1, 2 buttons
These buttons enable the various effects of
the selected side, either EFX 1 or EFX 2, to be
obtained for the master output signals.
e
BOOTH LEVEL control
Adjusts the level of the BOOTH outputs.
r
USB ASSIGN CH/MASTER button
This is used to switch the assignment destination
of the USB audio input signals supplied from the
computer.
CH:
The signals are assigned to the channels (1 to 4).
MASTER:
The signals are assigned to the master bus and
monitor bus.
t
MIDI CLOCK START/STOP button
This enables the MIDI clock corresponding to
the BPM value to be sent from the USB MIDI
and MIDI output terminals to the computer
(software) or external device.
START:
Sending the MIDI clock is started.
STOP:
Sending the MIDI clock is stopped.
y
UTILITY/–USB A/USB B button
This allows the presets to be set and the system
information to be set, changed or referenced.
When it is held down for more than a second,
the USB mode switching screen is opened, and
the USB device mode or USB host mode can
be selected.
u
BEAT , buttons
(Short) :
The beat/time is decreased.
(Long) :
The beat/time is increased.
i
TAP LOCK/AUTO/INPUT BPM button
TAP:
When this button is tapped repeatedly, the BPM
(Beats Per Minute) value is measured using the
intervals between the taps.
LOCK:
When the button is pressed once in the auto BPM
mode, the BPM value measured automatically is
locked.
AUTO BPM:
When the button is held down for one second,
the auto BPM mode is established, and the
measured BPM value is displayed.
INPUT BPM:
When it is held down for two or more seconds,
the BPM input mode is established, and the
BPM value can be input directly using the
u BEAT
, buttons. When it is pressed
again, the mode is released.
o
TIME/BACK button
TIME:
This button is used to select whether to change
the effects produced using the u BEAT ,
buttons on the basis of the number of beats
or time.
BACK (EFX 2 side only):
This is used when returning to the previous
screen while setting screen operations are
being performed.
Q0
Effect CUE button
When this button is set to ON, the sound of the
effects (but not the DELAY, ECHO or REVERB
effects) can be monitored even if the effect OFF
status.
Q1
EFX SELECT control
This is for selecting the effect to be used.
Refer to the effect functions (page 9).
Q2
Parameter ON/OFF button
This is used to control the ON and OFF settings
of the effect parameters.
Q3
PARAMETER MIX/MAX control
This is used to adjust the fi lter cutoff frequency
and other effector parameters. The parameters
are changed by the effector selected.
Q4
DRY/WET control
Use this to adjust the ratio of original and
effected sound.
Getting Started