Filter
Top Products
17
)
DIRECT O UT WITH SIGNAL
INTERRUP TION TO MASTER
INSERT ALL THE WAY IN TO
THE "SECOND CLICK"
MONO PLUG
TIP OUT TO EFFECTS DEVICE
RING RETURN FROM EFFECTS
STEREO
PLUG
FOR USE AS AN EFFECTS LOOP
(T IP = SEND, RING = RETURN )
SERIAL NUMBER
MANUFACTURING DATE
RISK OF ELECTRIC SHOCK
DO NOT OPEN
REPLACE WITH THE SAME TYPE FUSE AND RATING.
DISCONNECT SUPPLY CORD BEFORE CHANGING FUSE
UTILISE UN FUSIBLE DE RECHANGE DE MÊME TYPE.
DEBRANCHER AVANT DE REMPLACER LE FUSIBLE
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. DO NOT REMOVE COVER.
NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.
CAUTION
AVIS:
RISQUE DE CHOC ELECTRIQUE — NE PAS OUVRIR
R
L
CONTROL
ROOM
MIC
+4
BAL/UNBAL
MAIN
OUTPUT
LEVEL
4
5
6
3
R/4
L/3
2
1
CHANNEL INSERT
BAL/UNBAL
ALT
OUTPUT
(
PRE-FADER / PRE EQ TIP SEND / RING RETURN
)
MAIN
LEFT
MAIN
RIGHT
POWER
ON
PHANTOM
ON
120 VAC 50/60 Hz 25W
500mA/250V SLO-BLO
TO REDUCE THE RISK OF
FIRE REPLACE WITH SAME
TYPE FUSE AND RATING
CAUTION:
BALANCED BALANCED
DESIGNED BY MACKOIDS IN WOODINVILLE, WA, USA • COPYRIGHT ©1998
THE FOLLOWING ARE TRADEMARKS OR REGISTERED TRADEMARKS OF MACKIE DESIGN INC.: "MACKIE", "VLZ", "XDR", AND THE "RUNNING MAN" FIGURE • PATENT PENDING
XDR
TM
EXTENDED DYNAMIC RANGE MIC PREAMPLIFIERS ARE PROPRIETARY TO MACKIE DESIGNS, INC.
1402-VLZPRO
14-CHANNEL MIC/LINE MIXER
WITH PREMIUM XDR
TM
MIC PREAMPLIFIERS
POWER CONNECTION
Just in case you lose the cord provided with
the 1402-VLZ
PRO, its power jack accepts a
standard 3-prong IEC cord like those found on
most professional recorders, musical instru-
ments, and computers.
At the other end of our cord is — get this
— a plug! Not a black cube or, as we’re fond of
calling them, a “wall wart.” We did this for
some very good reasons:
The 1402-VLZ
PRO has sophisticated power
requirements that a wall wart cannot provide.
Wall warts are inconvenient, fragile, radiate
huge hum fields, hog extra jacks on your
power strip and get in the way. If you lose a
wall wart, you’re in trouble, but if you lose the
1402-VLZ
PRO’s power cord, you can get a new
one at any electronics, music, or computer
store. You can even buy them at Radio Shack
®
(part # 287-1257). Can you tell that we hate
wall warts?
Plug the 1402-VLZ
PRO into any standard
grounded AC outlet or into a power strip of
proper voltage.
WARNING: Disconnect-
ing the plug’s ground
pin can be dangerous.
Please don’t do it.
FUSE
The 1402-VLZ
PRO is fused for your (and its
own) protection. If you suspect a blown fuse,
disconnect the cord, pull the fuse drawer out
(located just below the cord receptacle) and
replace the fuse with a 500mA (0.5 amps) SLO
BLO, 5x20mm, available at electronics stores
or your dealer (or a 250mA SLO BLO 5x20mm
if your 1402-VLZ PRO is a 220V–240V unit).
If two fuses blow in a row, something is
very wrong. Please call our toll-free number
(or the distributor in your country) and find
out what to do.
POWER SWITCH
If this one isn’t self-explanatory, we give up.
You can leave this switch on all the time; the
1402-VLZ
PRO is conservatively designed, so
heat buildup isn’t a problem even in 24-hour-a-
day operation. There’s nothing that will burn out
or get used up. Or, just plug everything into a
good quality power strip for one-button turn-on.
You may notice that
the 1402-VLZ
PRO feels
quite warm in the upper-
right corner. This is
perfectly normal.
(Perfectly normal. Is that redundant?)
In the output section there is a
POWER
LED. If the power is on, so is the LED.
PHANTOM SWITCH
The Phantom Power Switch controls the
phantom power supply for condenser micro-
phones plugged into channels 1-6 mic inputs
as discussed at the start of this section
.
When turned on (or off), the phantom power
circuitry takes a few moments for voltage to
ramp up (or down). This is also perfectly normal.
In the output section, next to the
POWER
LED, is the
PHANTOM
LED. If the phantom
power is on, so is the LED.