3
Owner’s Manual
Owner’s Manual
Part No. SW0681 Rev. E
©2009 LOUD Technologies Inc. All Rights Reserved.
Loosely based on a dream sequence in which the entire Mackie marketing
department tap-dance their way into downtown Woodinville for lunch.
Ready, steady, go!
1. Turn the channel level, mon 1, and FX/mon 2
controls fully down.
2. Turn down the compressor controls (ch. 1–4).
3. Set all the EQ controls to the center, including
the graphic EQ sliders.
4. Turn down the main level and monitor 1 level
controls, and turn on the powered mixer.
5. For each channel, press the gain switch in (low
gain) if you are using a line-level source. Press
it out (high gain) if you are using a microphone
or other low-level source.
6. For condenser mics, push in the phantom
power switch. If you are using both condenser
and dynamic mics, don’t worry. Phantom power
will not hurt most dynamic mics. Check the
micro phone’s user manual if you’re not sure.
7. Play something into an input at real-world lev-
els, and turn up the channel level to U (unity).
8. In normal playing, the channel's OL LED should
only light occasionally. If it stays on for a large
portion of your performance, check that the
gain switch is set correctly.
9. Slowly turn up the main level control until you
hear the signal in your speakers.
10. Repeat steps 5 to 8 for the remaining channels.
11. If needed, apply some EQ wisely.
12. Adjust the levels to get the best mix. Keep the
level controls fully down on unused channels.
Other Notes
• Onlyconnectthepoweredmixer'sspeaker-level
outputs to passive loudspeakers.
• Whenshuttingdown,turnoffanyexternal
amplifiers or powered loudspeakers first. When
powering up, turn on any external amplifiers or
powered loudspeakers last.
• Savetheshippingbox!
Read This Page!
We realize that you must be really keen
to try out your new powered mixer, but
please read the safety instructions on
page 2, and this page first.
Setup
The PPM608 powered mixer is designed for ease of
operation, and to be set up quickly and easily.
Place the powered mixer in a position where it is easy
to reach the controls. All the controls and input con-
nection points are located on the front panel so you can
make quick adjustments and connections on stage.
Make sure there is at least 6 inches of airspace behind
the powered mixer for ventilation. There are two fans
inside the cabinet to cool the power amplifier section.
Use the powered mixers in a nice clean and dry environ-
ment, free from dryer lint and dust bunnies.
Connections
1. Be sure the rear-panel power switch is off
before making any connections.
2. Push the linecord securely into the IEC connec-
tor on the rear panel, and plug the other end
into a 3-prong AC outlet that is properly config-
ured for the voltage of your powered mixer.
3. Plug a balanced microphone into one of the mic
XLR (3-pin) connectors on the front panel. Or
you can connect any line-level signal (key-
board, or guitar preamp) to a line input jack
using a TS or a TRS 1/4" plug.
4. You can connect a guitar directly to inputs 5 or
6 without need for a DI box, if you press the hi-z
switch on these channels.
5. The insert jacks are used if you want to connect
an external effects or dynamics processor into
the signal chain. See page 13 for more details.
6. Plug the speakers (4 ohms or greater) into the
speaker output jacks on the rear panel. If you
plug two speakers into a side, each speaker
must be 8 ohms or greater to maintain a 4-ohm
minimum load on the amplifier. Use at least
18 gauge speaker cable with 1/4" TS plugs or
Speakon
®
plugs. For now, set the rear panel
power amp mode switch to stereo mains.
Don’tuseguitarcordsforspeakercables!
They’re not designed to handle speaker-level
signals and could overheat.
Please write your serial number here for future
reference (i.e., insurance claims, tech support,
return authorization, make dad proud, etc.)
Purchased at:
Date of purchase: