Filter
Top Products
26
En
REV ROLL
1
2
Effect turned on
Reversed and repeated
Original
1/1 reverse
roll
This function records the input sound at the point at which the [ON/OFF]
button is pressed, reverses the recorded sound and repeats it according
to the beat button’s fraction.
Beat buttons (parameter 1)
The effect time is set from 1/8 to 4/1 with respect to
1 beat of BPM time.
TIME control (parameter 2)
Use this to set the effect time.
10 to 4000 (ms)
LEVEL/DEPTH control
(parameter 3)
Use this to set the balance between the original
sound and ROLL.
EFFECT FREQUENCY
(parameter 4)
Use these to set the balance between the original
sound and the ROLL for the different bands.
FILTER
1
Frequency
This function changes the filter’s cut-off frequency according to the beat
button’s fraction.
Beat buttons (parameter 1)
These set the cycle for moving the cut-off frequency
from 1/8 to 4/1 with respect to 1 beat of BPM time.
TIME control (parameter 2)
Use this to set the cycle at which the cut-off fre-
quency is moved.
10 to 32000 (ms)
LEVEL/DEPTH control
(parameter 3)
The further the control is turned clockwise, the more
the effect is stressed.
The original sound is set when turned fully
counterclockwise.
EFFECT FREQUENCY
(parameter 4)
These set the balance between the original sound
and the effect sound for the different bands.
TRANS
1
MIN MAX
MIN MAX
EFFECT FREQUENCY
MIN MAX
Cut
Cut Cut
Cut
1/1 beat
Time
This function cuts the sound according to the beat button’s fraction.
The amount of the sound to be cut can be changed at
[EFFECT FREQUENCY].
Beat buttons (parameter 1)
These set the 1/8 to 4/1 cut time with respect to 1
beat of BPM time.
TIME control (parameter 2)
Use this to set the effect time.
10 to 16000 (ms)
LEVEL/DEPTH control
(parameter 3)
Sets the balance between the original sound and the
effect sound.
EFFECT FREQUENCY
(parameter 4)
This sets the amount of the original sound to be cut
for the different bands.
PHASER
1
Cycle
Phase shift
Time
The phaser effect changes according to the beat button fraction.
Beat buttons (parameter 1)
These set the cycle for moving the phaser effect by
1/8 to 4/1 with respect to the time of one BPM beat.
TIME control (parameter 2)
This sets the cycle by which the phaser effect is
moved.
10 to 32000 (ms)
LEVEL/DEPTH control
(parameter 3)
The further the control is turned clockwise, the more
the effect is stressed.
When turned all the way counterclockwise, only the
original sound is output.
EFFECT FREQUENCY
(parameter 4)
Use these to set the balance between the original
sound and the effect sound for the different bands.
GATE
1
MIN MAX
MIN MAX
EFFECT FREQUENCY
MIN MAX
Threshold
Threshold
Level
Threshold
Time
This function outputs the input sound that has a level above the thresh-
old level, cutting the input sound that has a level below the threshold
level.
The threshold level can be changed at [EFFECT FREQUENCY].
Beat buttons (parameter 1) This sets the release time between 1 and 100 %.
TIME control (parameter 2)
This sets the release time.
1 to 100 (%)
LEVEL/DEPTH control
(parameter 3)
Sets the threshold level.
The further the control is turned clockwise, the more
the effect is stressed and the sound is cut.
EFFECT FREQUENCY
(parameter 4)
Use these to set the threshold levels for the different
bands.
SEND/RETURN
1
DJM-2000NXS
SEND
RETURN
Effector
Connect an external effector, etc., here.
[EFFECT FREQUENCY] can be used as an isolator.
Beat buttons (parameter 1) —
TIME control (parameter 2) —
LEVEL/DEPTH control
(parameter 3)
This adjusts the sound level input to the [RETURN]
terminal.
EFFECT FREQUENCY
(parameter 4)
This sets the audio output level of the RETURN
sound for the different bands.
1 When “A”, “B” or “M” is selected with the [CH SELECT] buttons, the
effect sound cannot be monitored by pressing [CUE] (BEAT EFFECT)
unless the sound for the channel you want to monitor is being output
from [MASTER] channel.
2 When BEAT EFFECT is off, the effect sound cannot be monitored by
pressing [CUE] (BEAT EFFECT).