Filter
Top Products
28
En
Additional information
Troubleshooting
! Incorrect operation is often mistaken for trouble or malfunction. If you think that there is something wrong with this component, check the points
below. Sometimes the trouble may lie in another component. Inspect the other components and electrical appliances being used. If the trouble
cannot be rectified after checking the items below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.
! The player may not operate properly due to static electricity or other external influences. In such cases, normal operation may be restored by
unplugging the power cord then plugging it back in.
Problem Check Remedy
The power is not turned on. Is the power cord properly connected? Plug in the power cord to an AC outlet.
No sound or small sound. Is the [CD/DIGITAL, PHONO, LINE, USB */*]
switch set to the proper position?
Switch the [CD/DIGITAL, PHONO, LINE, USB */*] switch to the channel’s input
source. (page 12)
Are the [CD, DIGITAL] switches on the rear panel
properly set?
Set the [CD, DIGITAL] switches according to the devices to be played. (Page 12)
Are the connection cables properly connected? Connect the connection cables properly. (page 7)
Are the terminals and plugs dirty? Clean the terminals and plugs before making connections.
Is the [MASTER ATT.] switch on the rear panel set
to [–6 dB], etc.?
Switch the [MASTER ATT.] switch. (page 6)
Digital sound cannot be output. Is the digital audio output’s sampling frequency
(fs) suited for the specifications of the connected
device?
On the [CLUB SETUP] screen, set [DIGITAL SAMPLING RATE] according to the
specifications of the connected equipment. (page 27)
Distorted sound. Is the sound level output from the [MASTER] chan-
nel appropriately set?
Adjust the [MASTER] control so that the master channel level indicator lights at
around [0 dB] at the peak level. (Page 12)
Set [MASTER ATT.] to [–3 dB] or [–6 dB]. (page 6)
Is the level of audio input to each channel properly
set?
Adjust the [TRIM] control so that the channel level indicator lights at about
[0 dB] at the peak level. (Page 12)
Can’t crossfade. Are the CROSS FADER ASSIGN (A, THRU, B)
selector switches properly set?
Set the [CROSS FADER ASSIGN (A, THRU, B)] selector switches for the different
channels properly. (Page 12)
Can’t fader start a DJ player. Is [FADER START] set to [OFF]? At the [USER SETUP] screen, set [FADER START] to [ON]. (page 13)
Is the DJ player properly connected to the
[CONTROL] terminal?
Connect the [CONTROL] terminal and DJ player using a control cord. (page 7)
Is the DJ player properly connected to the [LINK]
terminal?
Connect the DJ player to the [LINK] terminal properly using a LAN cable. (page
7)
Are the audio cables properly connected? Connect this unit’s audio input terminals and the DJ player’s audio output
terminals by audio cable. (page 7)
BEAT EFFECT function does not work. Are the [CH SELECT] buttons properly set? Press the [CH SELECT] button(s) to select the channel(s) to which you want to
add the effect.
[INST FX] does not work. Is the [FILTER] control set to the proper position? Turn the [FILTER] control clockwise. (page 18)
Can’t use an external effector. Is the [ON/ OFF] button for [BEAT EFFECT] set
to [ON]?
Press [ON/OFF] for the BEAT EFFECT to turn [SEND/RETURN] on. (page 18)
Is the external effector properly connected to the
[SEND] or [RETURN] terminal?
Connect the external effector to the [SEND] and [RETURN] terminals. (page 7)
Distorted sound from an external
effector.
Is the external effector’s audio output level set to
an appropriate level?
Adjust the external effector’s audio output level.
Tempo (BPM) cannot be measured or
measurement value of tempo (BPM) is
implausible.
Is the audio input level too high or too low? Adjust the [TRIM] control so that the channel level indicator lights at about
[0 dB] at the peak level. (Page 12)
For some tracks, it may not be possible to measure the tempo (BPM). Use the
[TAP] button to input the tempo manually. (page 18)
Measured tempo (BPM) differs from
tempo indicated on CD.
— The values may differ slightly due to the different ways in which the BPM is
measured.
MIDI sequencer does not synchronize. Is the MIDI sequencer’s sync mode set to Slave? Set the MIDI sequencer’s sync mode to Slave.
Does the MIDI sequencer you are using support
MIDI timing clocks?
MIDI sequencers not supporting MIDI timing clocks cannot be synchronized.
MIDI control does not work. Is the MIDI channel turned on? Press the [ON/ OFF] button for [MIDI]. (page 19)
Are the MIDI settings properly set? To operate DJ software with this unit, this unit’s MIDI messages must be
assigned to the DJ software you are using. For instructions on assigning mes-
sages, see your DJ software’s operating instructions.
This unit is not recognized after it has
been connected to a computer.
Is the driver software properly installed on your
computer?
Install the driver software. If it is already installed, reinstall it. (page 8)
Sound of a computer cannot be
output from this unit.
Are this unit and computer properly connected? Connect this unit and computer using a USB cable. (page 8)
Are the audio output device settings properly set? Select this unit with the audio output device settings. For instructions on making
settings for your application, see your application’s operating instructions.
Is this unit’s input selector switch properly set? Set the channel’s input selector switch to the [USB */*] position. (Page 12)
Nothing happens when touch panel
is pressed.
Touch panel’s calibration is off. Adjust the touch panel with the [TOUCH PANEL] settings at the [CLUB SETUP]
screen. (page 27)
Effect sound cannot be monitored
even when the [CUE] button for [BEAT
EFFECT] is pressed.
— The circuit that generates the echo for the [ECHO], [REVERB], [ROLL],
[SLIP ROLL] and [REV ROLL] effect sounds is positioned after the effect circuit,
so the effect sound cannot be monitored. This is not a malfunction.