Trane RX-212 Music Mixer User Manual


 
Input & Output Specifications
INPUT SPECIFICATIONS
0dB is referenced to 0.775V RMS.
Input
CHANNEL IN
BAL –60
BAL –40
BAL –20
UN-BAL
ACCESSORY
(RCV)
STEREO IN
AUX
PHONO
AUX ECHO IN
SUB IN
Actual
Load
Impedance
550 ohms
800 ohms
900 ohms
25k ohms
10k ohms
10k ohms
47k ohms
10k ohms
10k ohms
For Use
With
Nominal
50 to 600
ohms
10k ohms
10k ohms
10k ohms
4 7k ohms
10k ohms
10k ohms
Sensitivity*
–80dB (0.08mV)
–60dB (0.78mV)
–40dB (7.8mV)
–50dB (2.5mV)
-20dB (78mV)
–40dB (7.8mV)
–70dB (0.25mV)
-40dB (7.8mV)
–10dB (250mV)
Input Level (Trim "0" to Trim "–30")
Nominal
–60dB (0.78mV) to –30dB (25mV)
–40dB (7.8mV) to –10dB (250mV)
–20dB (78mV) to +10dB (2.5V)
–30dB (25mV) to 0dB (775mV)
–0dB (775mV)
–20dB (78mV)
–50dB (2.5mV)
-20dB (78mV)
+4dB (1.23mV)
MAX. Before Clip
–40dB (7.8mV) to –10dB (250mV)
–20dB (78mV) to +10dB (2.5V)
0dB (775V) to +30dB (25V)
–10dB (250mV) to +20dB (7.8V)
20dB (7.8mV)
+10dB (2.5V)
–20dB (78mV)
0dB (775mV)
+24dB (12.3mV)
Connector
XLR-3-31
type**
PHONE JACK
3P PHONE
JACK***
RCA
PIN JACK
PHONE JACK
PHONE JACK
OUTPUT SPECIFICATIONS
0dB is referenced to 0.775V RMS.
Output
PGM L
LI NE OUT
PGM R
FBl
FB2
ECH O S EN D
+4
-20
REC OUT
ACCESSORY (SEND)
PHONES
Actual Source Impedance
100 ohms
90 ohms
64 ohms
1k ohms
1k ohms
18 ohms
For Use With Nominal
600 ohms
600 ohms
10k ohms
10k ohms
8 ohms or higher
Output Level
Nominal
+4dB (1.23V)
+4dB (1.23V)
–20dB (78mV)
–10dB (250mV)
0dB (775mV)
75mW/8 ohms,
0dB (775mV)
MAX Before Clip
+20dB (7.8V)
+20dB (7.8V)
-4dB (490mV)
+10dB (2.5V)
+20dB (7.8V)
370mW/8 ohms,
+7dB (1.7V)
Connector
XLR-3-32
type**
and
PHONE JACK
PHONE JACK
PHONE JACK
RCA PIN JACK
3P PHONE JACK***
STEREO
PHONE JACK****
*Sensitivity is the level required to produce a nominal speaker output level.
**All XLR type connectors are floating, balanced and transformer-isolated.
***ACCESSORY jacks (3P PHONE JACK) are wired: Tip=Receive, Ring=Send and Sleeve =Common
****Stereo phone jack is wired: Tip=Left, Ring=Right and Sleave=Common
Note:
As is described in the beginning of the operation manual, the XLR type connectors of the RX-208, RX-212 and RX-216 are wired as follows.
Pin No. 1 — Ground
Pin No. 2 — Cold (Low)
Pin No. 3 — Hot (High)
Specifications are subject to change without notice.
Caution:
The fuse rating for 120V AC operation is 2 amps., and 1 amp. for 220/240V AC operation. The fuse must always be replaced
with same type and rating.
-
15
-