Zoom G1XN Music Pedal User Manual


  Open as PDF
of 16
 
18
ZOOM G1N/G1XN
19
ZOOM G1N/G1XN
Using an External Foot Switch or Pedal (G1N only)
•Rhythmmode
When you press the foot switch two times or
more, the G1N detects the interval and
automaticallyadjuststhetempoaccordingly
(tap tempo function).
•Editmode/Storemode
The foot switch has no effect.
Using an expression pedal
When the optional expression pedal (FP01/
FP02)isconnectedtothe[CONTROLIN]
jackoftheG1N,youcanchangeeffect
parameters in real time or use the pedal as a
volume controller. The function of the
expression pedal can be saved individually for
each patch.
1.PlugtheFP01orFP02intothe
[CONTROLIN]jackoftheG1N.
2.Inplaymode,selectapatchfor
which you want to use the expression
pedal.
3. Set the Module selector to a position
other than "PLAY" or "RHYTHM".
The G1N/G1XN goes into edit mode.
4. Hold down the RHYTHM [
R
/
P
] key
and turn the [VALUE] knob to select
one of the following modules for
control by the expression pedal.
Display Control target
OF
Off
VP
Volume
WP
COMP/EFXmodule
GP
DRIVEmodule
MP
MODULATIONmodule
DP
DELAYmodule
RP
REVERBmodule
· In the section "Effect Types and
Parameters" (
g
p. 21), effect types/
parameters that can be controlled with
the expression pedal are indicated by a
pedal symbol.
· If a module is selected for which no
pedal symbol is shown, the expression
pedal will have no effect for that patch.
5. Save the patch.
The expression pedal setting is stored with
the patch.
6. In play mode, select the patch and
operate the expression pedal.
The respective parameter changes.
In bypass mode, the expression pedal
always functions as a volume pedal,
regardless of the setting.
The expression pedal operates also in edit
mode.
Changing the Way Patches Are Called Up
This section describes how to change the patch selection method of the G1N/G1XN to "pre-
select". In this mode, you first select the patch to use next, and then perform an additional step to
activate the patch.
1.TurnpowertotheG1N/G1XNon
while holding down the [
Q
] foot
switch.
Theindication"PrE-SElEct"scrollsonthe
display.
2.Inplaymode,selectthepatchtouse
next.
The selected new bank and patch number
flash on the display. The sound does not
change yet.
3. When you have specified the patch to
use, press both [
W
]/[
Q
] foot switches
together.
The patch change is accepted, causing the
sound to change, and the display changes
from flashing to permanently lit.
4.
ToreturntheG1N/G1XNtothenormal
patch selection method, simply turn
power off and then on again.
The patch selection method is automatically
reset to conventional operation.
Using an External Foot Switch or Pedal (G1N only)
The[CONTROLIN]jackontheG1Nallowsconnectionofanoptionalfootswitchorexpression
pedal to control effects and the rhythm function. This section explains how to use this capability.
Using a foot switch
Simply connect the optional foot switch (FS01)
tothe[CONTROLIN]jackoftheG1Nand
turn the unit on. This allows you to switch
banks and specify the tempo for rhythm
patterns with the foot switch.
Depending on the currently selected mode, the
foot switch operates as follows.
•Playmode
Pressing the foot switch selects the next
higher bank.
B0 B0
B0
HINT
HINT
B0 B0
 previous next