Filter
Top Products
18
DE-10 Owner’s Manual
How to use the Dual Mode
We describe how to use the Dual Mode below.
<About features of the Dual Mode>
1. You can use the DE-10 as a two-channel effect processing unit.
2. Each effect processor (EFFECT 1 and EFFECT 2) provides a mono input and stereo output jacks.
3. A main parameter for each effect can be edited from the preset value.
The following shows the example of using the dual mode, in which the DE-10 is connected between the AUX SEND
and AUX RTN jacks for applying the desired effect to a sound.
MIC/GLINE
TRIM
GUITAR
MIC
model 8051
SINGLE MODE
DUAL MODE
2
(MONO)
1 (1&2)
LINE INPUT (-10dBV)OUTPUT 2 OUTPUT 1EFF MUTE
MAX
MIN
MIN
MAX
MIC/GUITAR INPUT
FOOT SW
R
R
L
(MONO)
R
L
L(MONO)
MIC/GLINE
MIXER
AUX SEND
AUX RTN
Adjust the incoming signal level
from the mixer. See <Caution on
Effect Processing> below for details
about how to adjust the level.
Set the input se-
lector to "LINE".
<Point>
Connect the Foot SW
into the jack to re-
motely control the
Effect Mute ON/OFF.
PEAK PEAK
ADJUST
1
TYPE
VARIATION
DELAY
PITCH
FLANGE
VOCAL
L.HALL
ROOM
DLY+REV
S.HALL
PLATE MISC
CHO
5
1
1
7
3
6
2
4
10
8
9
TYPE VARIATION
G
J
K
E
A
C
MIX
EFF
DRY
DUALSINGLE1
F
B
DH
I
5
1
11
7
3
6
2
4
10
8
9
EFF
DRY
DRY+EFF
DRY+EFF
POWER
CHORUS
MISC
FLANGER
PITCH
DELAY DISTORTION
G.MULTI 1
G.MULTI 2
B.MULTI
VO.MULTI
G
J
K
H
I
SINGLE 2SINGLE1/DUAL
MODE
MODE
SINGLE2
PARAM.2
MIX
PARAM.3
EFF MUTE
EFFECT 2
ADJUST
PARAM.1
2
3
4
5
1
234
5
<About PEAK indicator>
The PEAK indicator on the front panel illuminates when
the input signal to be monitored reaches 6 dB below the
clipping level. Adjust the input level appropriately so
that the PEAK indicator occasionally flickers. If you hear
the output sound distorted though the PEAK indicator
does not steadily light or illuminate so often, it may be
due to the signal level increase in the effect processing.
In such a case, reduce the input level so that the output
sound is not distorted.
<Note on changing the switch position>
When you change the position of the MODE, EFFECT TYPE,
or VARIATION switch, the DE-10 resets the internal DSP
and the output signal disappears momentarily. This is
due to not a malfunction.
<Notes on using the ADJUST and MIX controls>
• When you turn the ADJUST or MIX control, a click may
be generated with some effect type.
• If the default of a parameter is the maximum or
minimum value, you cannot increase or decrease the
value using the ADJUST control, respectively.
<Front panel settings>
1.Set the MODE switch to "DUAL".
2.Set the TYPE switch for each of EFFECT 1 and 2 to the
desired position.
You can select from among the following eleven types.
See page 5~7 for details about each type.
3.Set the VARIATION switch for each of EFFECT 1 and 2 to
the desired position.
4.Using the appropriate ADJUST control, adjust the
parameter for each of EFFECT 1 and 2.
5.Using the appropriate MIX control, adjust the mixing
balance of dry and effect signals fed from the OUTPUT
jacks for each of EFFECT 1 and 2.
MODE
SINGLE 1/DUAL SINGLE 2
SINGLE 1/DUAL SINGLE 2
A
B
C
D
E
F
G
H
I
J
K
L. HALL
S. HALL
ROOM
PLATE
VOCAL
DELAY + REV
L. HALL
S. HALL
ROOM
PLATE
MIC SIM
AMP SIM
DELAY
MISC
CHORUS
PITCH
FLANGER
DISTORTION
G. MULTI 1
G. MULTI 2
B. MULTI
VO. MULTI
SW
MODE
SW