Filter
Top Products
DRB1497-B
En
23
English
2322
REV ROLL
1
2
Effect turned on
Reversed and repeated
Original
1/1 reverse
roll
This function records the input sound at the point at which the [ON/
OFF] but-
ton is pressed, reverses the recorded sound and repeats it according to the beat
button’s fraction.
Beat buttons (parameter 1)
The effect time is set from 1/8 to 4/1 with respect to 1 beat of
BPM time.
TIME (parameter 2)
Use this to set the effect time.
10 to 4000 (ms)
LEVEL/
DEPTH (param-
eter 3)
Use this to set the balance between the original sound and
ROLL.
EFFECT FREQUENCY
(parameter 4)
Use these to set the balance between the original sound and
the ROLL for the different bands.
FILTER
1
Frequency
This function changes the filter’s cut-off frequency according to the beat button’s
fraction.
Beat buttons (parameter 1)
These set the cycle for moving the cut-off frequency from 1/8 to
4/1 with respect to 1 beat of BPM time.
TIME (parameter 2)
Use this to set the cycle at which the cut-off frequency is
moved.
10 to 32000 (ms)
LEVEL/
DEPTH (param-
eter 3)
The further the control is turned clockwise, the more the effect
is stressed.
EFFECT FREQUENCY
(parameter 4)
These set the balance between the original sound and the
effect sound for the different bands.
TRANS
1
MIN MAX
MIN MAX
EFFECT FREQUENCY
MIN MAX
Cut
Cut Cut
Cut
1/1 beat
Time
This function cuts the sound according to the beat button’s fraction.
The amount of the sound to be cut can be changed at [EFFECT FREQUENCY].
Beat buttons (parameter 1)
These set the 1/8 to 4/1 cut time with respect to 1 beat of BPM
time.
TIME (parameter 2)
Use this to set the effect time.
10 to 16000 (ms)
LEVEL/
DEPTH (param-
eter 3)
Sets the balance between the original sound and the effect
sound.
EFFECT FREQUENCY
(parameter 4)
This sets the amount of the original sound to be cut for the
different bands.
PHASER
1
Cycle
Phase shift
Time
The phaser effect changes according to the beat button fraction.
Beat buttons (parameter 1)
These set the cycle for moving the phaser effect by 1/8 to 4/1
with respect to the time of one BPM beat.
TIME (parameter 2)
This sets the cycle by which the phaser effect is moved.
10 to 32000 (ms)
LEVEL/
DEPTH (param-
eter 3)
The further the control is turned clockwise, the more the effect
is stressed.
When turned all the way counterclockwise, only the original
sound is output.
EFFECT FREQUENCY
(parameter 4)
Use these to set the balance between the original sound and
the effect sound for the different bands.
GATE
1
MIN MAX
MIN MAX
EFFECT FREQUENCY
MIN MAX
Threshold
Threshold
Level
Threshold
Time
This function outputs the input sound that has a level above the threshold level,
cutting the input sound that has a level below the threshold level.
The threshold level can be changed at [EFFECT FREQUENCY].
Beat buttons (parameter 1) This sets the release time between 1 and 100 %.
TIME (parameter 2)
This sets the release time.
1 to 100 (%)
LEVEL/
DEPTH (param-
eter 3)
Sets the threshold level.
The further the control is turned clockwise, the more the effect
is stressed and the sound is cut.
EFFECT FREQUENCY
(parameter 4)
Use these to set the threshold levels for the different bands.
SEND/RETURN
1
DJM-2000
SEND
RETURN
Effector
Connect an external effector, etc., here.
[EFFECT FREQUENCY] can be used as an isolator.
Beat buttons (parameter 1) —
TIME (parameter 2) —
LEVEL/
DEPTH (param-
eter 3)
This adjusts the sound level input to the [RETURN] terminal.
EFFECT FREQUENCY
(parameter 4)
This sets the audio output level of the RETURN sound for the
different bands.
1 When “A”, “B” or “M” is selected with the [CH SELECT] buttons, the effect sound
cannot be monitored by pressing [CUE] (BEAT EFFECT) unless the sound for
the channel you want to monitor is being output from [MASTER] channel.
2 When BEAT EFFECT is off, the effect sound cannot be monitored by pressing
[CUE] (BEAT EFFECT).