Filter
Top Products
11
<DRB1314>
PART NAMES AND FUNCTIONS
≠ Effect beat selector switches (@, #)
Use this switch to change the value of Effect
PARAMETER 1 control (‹) in accordance with the BPM
of the source selected with the Effect CH. SELECT
switch (¤). The setting value of this switch differs
depending on the setting of the Effect selector switch
(⁄).
¶ When DELAY, ECHO, PAN, or TRANS are selected, the
parameter 1 value for the BPM of the selected source
can be set to 1/4 beat, 1/2 beat, 1/1 beat, 2/1 beat, 4/1
beat, or 8/1 beat.
¶ When DELAY or ECHO are selected, values can be set
to 1/4x, 1/2x, 1/1x, 2/1x, 4/1x or 8/1x, within a range
such that the parameter 1 value does not exceed 3500
ms.
¶ When FILTER or FLANGER are selected, the parameter
1 value for the BPM of the selected source can be set
to 1/2 beat, 1 beat, 2 beats, 4 beats, 8 beats, 16 beats,
or 32 beats.
¶ When PITCH is selected, the value can be set to
–100%, –50%, –33%, 0%, 33%, 50%, or 100%.
¶ When REVERB is selected, the value can be set to
10%, 20%, 35%, 50%, 65%, 80%, or 90%.
¶ This control is disabled when AUTO BPM or SND/RTN
are selected.
Ÿ H.P CUE (Headphones cue switch)
When this switch is pressed it lights orange, and beat
effects are output to the headphones. Pressing the
switch again disconnects the beat effect to the
headphones and turns off the switch lamp.
⁄ Effect selector switch
Use to select desired effects (see page 12).
¤ CH. SELECT (Effect channel selector switch)
Use to select the source you wish to apply effects to.
‹ TIME (PARAMETER 1)
(Effect parameter 1 control)
This control is used to set the time parameter for the
onboard effector (see page 14).
› LEVEL/DEPTH (PARAMETER 2)
(Effect parameter 2 control)
This control is used to set quantitative parameters for the
onboard effector (see page 14).
fi ON/OFF, TAP (Effect ON/OFF switch, TAP switch)
This switch produces different operations depending on
the setting of the Effect selector switch (⁄)
¶ When DELAY, ECHO, PAN, TRANS, FILTER, FLANGER,
REVERB, PITCH, or SND/RTN are selected, the switch
operates to turn the selected effect ON/OFF.
OFF: the orange lamp lights; ON: orange lamp flashes.
¶ When AUTO BPM is selected the switch becomes a
“TAP” switch; by tapping the switch together with the
source beat, the BPM can be input manually.
When tapping the TAP switch to count the BPM, both
BPM counter range displays (70-139 BPM and 91-180
BPM) go out, and the manual mode is enabled (see
page 19).
Å EFFECT MIX Controls
fl FADER/OFF/AUTO (EFFECT MIX selector switch)
Use to select the cross fader effect mode.
FADER: Selects Effect Mix Fader mode. When this is
selected, the Cross fader lever (™) can be used
to control effects and perform cue start and back
cue.
OFF: Normal mode
AUTO: The Effect Mix Auto mode. When this is
selected, the Effect select/start switches (‡, °,
·) can be used to control effects, perform cue
start and back cue.
‡, °, · Effect select/start switches
Use to select the type of Effect Mix desired (default is
ECHO)
¶ The switch for the selected function flashes.
‡ ECHO switch
° ZIP switch
· ROLL switch