Filter
Top Products
9
<DRB1314>
PART NAMES AND FUNCTIONS
- LOW control (low-range equalizer)
Use to adjust low-range frequency of input.
When the dial is set to the center click setting, flat
response is provided.
Rotate clockwise to increase response (to +12 dB), and
rotate counterclockwise to decrease response (to –26
dB).
= H.P CUE (Headphones cue switch)
When this switch is pressed it lights orange and the
corresponding channel is output to headphones. When
the switch is pressed again the light goes out and the
channel’s output to the headphones is cut.
When the beat effector function is set to AUTO BPM, this
switch functions to select the BPM display channel.
~ Peak level meter
Peak levels are displayed as they occur and maintained
for 2 seconds.
The meter displays the channel fader output level.
Displayable range is from –22 dB to +14 dB.
! Channel fader lever
Use to adjust the sound level at each channel.
π MASTER (Master Controls)
@ MONO/STEREO selector switch
Use to select whether the master output and booth
monitor output are monaural or stereo.
# MASTER LEVEL meter
Displays output level following adjustment of the
MASTER fader lever, and holds the display for 2 seconds.
Displayable range is from –22 dB to +14 dB.
$ H.P CUE (Headphones cue switch)
When this switch is pressed it lights orange and the
master output is heard in the headphones. When the
switch is pressed again the light goes out and the master
output to the headphones is cut.
% MASTER fader lever
Use to control the master output level.
The rear panel MASTER LEVEL ATT. control can also be
used to reduce the output level.
^ MASTER BALANCE control
Use to adjust the balance of right-left channels for master
output and booth monitor output.
[ BOOTH MONITOR Control
Use to adjust the output at the BOOTH MONITOR
connectors on the rear panel. Not affected by the
MASTER fader lever (%).
“ POWER Switch
] HEADPHONES Controls
& MONO SPLIT/STEREO selector switch
Use to select whether to split monitor sound on the left
and right of the headphones or to keep sound in stereo
form.
When set to MONO SPLIT, the headphones output is set
to 2-channel monaural; the Left channel becomes the
source selected with the H.P CUE switch, while the Right
channel becomes the master output sound (only when
MASTER H.P CUE switch is set to ON).
* MIXING control
Use to adjust the headphones monitor sound.
When rotated fully clockwise, the master output sound
only is heard (only when MASTER H.P CUE switch is set
to ON). When rotated fully counterclockwise, only the
channel selected with the H.P CUE switch (other than
MASTER) is heard.
At the center click position, the master output and source
selected with the H.P CUE switch are at equal levels.
( LEVEL control
Use to control the headphones monitor level. When one
of CH-1 to CH-4 is selected, this control is not affected by
the MASTER fader lever (%) and the MASTER BALANCE
control (^).
) PHONES (headphones jack)
‘ Cross Fader Controls
_ CROSS FADER ASSIGN A switch
When using the cross fader with two sources (A, B), this
switch selects the source assigned to A.
THRU: When cross fader is not used, sets to THRU.
1-4: Use to select the channel (CH-1 to CH-4) assigned
to A.
Channels other than those assigned to A and B
can be output without passing through the cross
fader.
+ CROSS FADER CURVE selector switch
Use to select one of three rising curve patterns for the
cross fader function.
¡ Fader display A
During the effect mix mode, displays the output of
sounds from the channel selected with the CROSS
FADER ASSIGN A switch.
™ Cross fader lever
Use to adjust the mix of sounds from the sources
assigned to A and B by the ASSIGN switches (_) and (¢).
£ Fader display B
During the effect mix mode, displays the output of
sounds from the channel selected with the CROSS
FADER ASSIGN B switch.
¢ CROSS FADER ASSIGN B switch
When using the cross fader with two sources (A, B), this
switch selects the source assigned to B.
THRU: When cross fader is not used, sets to THRU.
1-4: Use to select the channel (CH-1 to CH-4) assigned
to B.
Channels other than those assigned to A and B
can be output without passing through the cross
fader.
\ FADER START Switches
CH-1, CH-2, CH-3, CH-4
When a CD player (CMX-3000, CMX-5000, CDJ-1000,
CDJ-100S, CDJ-700S or CDJ-500II) is connected to one of
the above channels of this unit via a control cord, the CD
player’s CUE START/STOP operation will start when the
channel fader is moved from “0” upwards, and will stop
(back cue) when the channel fader is returned to “0”. The
indicator of the selected channel will light orange during
this operation. Also, if a channel is assigned to the cross
fader, the cross fader is given priority; when the Cross
fader lever begins moving from the A side toward B side,
the CD player assigned to the B side will start, and when
the lever reaches the B side, the A side source will stop
(back cue).