Filter
Top Products
34
Effect List
&52#.)14+6*/.+56
0WODGT 0COG (WPEVKQP 2CTCOGVGTU
00 Auto Pan
Continually performs left-right panning of the
input signal in accordance with an LFO.
0: Rate (0 to 127) – Adjusts the panning rate.
1: Depth (0 to 127) – Adjusts the panning depth.
01 Tremolo
– Adjusts volume of input signal in accordance
with an LFO.
0: Rate (0 to 127) – Adjusts the tremolo rate.
1: Depth (0 to 127) – Adjusts the tremolo depth.
02 2BandEQ This is a two-band equalizer.
0: Low Frequency [0 (200Hz), 1 (400Hz), 2 (800Hz)] – Adjusts the cutoff
frequency of the low-band equalizer.
1: Low Gain (-12, -11, -10 to +10, +11, +12) – Adjusts the gain of the low-band
equalizer.
2: High Frequency [0 (6.0kHz), 1 (8.0kHz), 2 (10kHz)] – Adjusts the cutoff
frequency of the high-band equalizer.
3: High Gain (-12, -11, -10 to +10, +11, +12) – Adjusts the gain of the high-band
equalizer.
03 3BandEQ This is a three-band equalizer.
0: Low Frequency [0 (200Hz), 1 (400Hz), 2 (800Hz)] – Adjusts the cutoff
frequency of the low-band equalizer.
1: Low Gain (-12, -11, -10 to +10, +11, +12) – Adjusts the gain of the low-band
equalizer.
2: Mid Frequency [0 (1.0kHz), 1 (1.3kHz), 2 (1.6kHz), 3 (2.0kHz), 4 (3.0kHz), 5
(4.0kHz), 6 (6.0kHz), 7 (8.0kHz)] – Adjusts the center frequency of the mid-
band equalizer.
3: Mid Gain (-12, -11, -10 to +10, +11, +12) – Adjusts the gain of the mid-band
equalizer.
4: High Frequency [0 (6.0kHz), 1 (8.0kHz), 2 (10kHz)] – Adjusts the cutoff
frequency of the high-band equalizer.
5: High Gain (-12, -11, -10 to +10, +11, +12) – Adjusts the gain of the high-band
equalizer.
04 LFO Wah
This is a “wah” effect that can automatically
affect the frequency in accordance with an LFO.
0: Input Level (0 to 127) – Adjusts the input level. The input signal can become
distorted when the level of the sound being input, the number of chords, or the
resonance value is large. Adjust this parameter to eliminate such distortion.
1: Resonance (0 to 127) – Adjusts the resonance of the sound.
2: Manual (0 to 127) – Adjusts the frequency used as the basis for the wah filter.
3: LFO Rate (0 to 127) – Adjusts the rate of the LFO.
4: LFO Depth (0 to 127) – Adjusts the depth of the LFO.
05 Auto Wah
This is a “wah” effect that can automatically
affect the frequency in accordance with the
level of the input signal.
0: Input Level (0 to 127) – Adjusts the input level. The input signal can become
distorted when the level of the sound being input, the number of chords, or the
Resonance value is large. Adjust this parameter to eliminate such distortion.
1: Resonance (0 to 127) – Adjusts the resonance of the sound.
2: Manual (0 to 127) – Adjusts the frequency used as the basis for the wah filter.
3: Depth (-64 to 0 to +63) – Adjusts the depth of the wah in accordance with the
level of the input signal. Setting a positive value causes the wah filter to open
in direct proportion with the size of the input signal, producing a bright sound.
Setting a negative value causes the Wah filter to close in accordance with the
size of the input signal, which produces a dark tone quality. However, large
input re-opens the Wah filter, even if it is closed.
06 Compressor
Compresses the input signal, which can
suppress level variation and make it possible to
sustain dampened sounds longer.
0: Depth (0 to 127) – Adjusts compression of the audio signal.
1: Attack (0 to 127) – Adjusts the attack amount of the input signal. A smaller
value causes prompt compressor operation, which suppresses the attack of
the input signal. A larger values delays compressor operation, which causes
attack to be output as-is.
2: Release (0 to 127) – Adjusts the time from the point when the input signal
drops below a certain level until the compression operation is stopped. When
an attack feeling is desired (no compression at the onset of the sound), set
this parameter to as low a value as possible. To apply compression at all
times, set a high value.
3: Level (0 to 127) – Adjusts the output level. The output volume changes in
accordance with the Depth setting and the characteristics of the input tone.
Use this parameter to correct for such changes.
07 Limiter
This is an effector that you can use to set an
upper limit value on the level of the input signal.
0: Limit (0 to 127) – Adjusts the volume level from which the limit is applied.
1: Attack (0 to 127) – Adjusts the attack amount of the input signal.
2: Release (0 to 127) – Adjusts the time from when the input signal drops below
a certain level until the limit operation stops.
3: Level (0 to 127) – Adjusts the level being output. The output volume changes
in accordance with the Limit setting and the characteristics of the input tone.
Use this parameter to correct for such changes.
08 Distortion This effect provides Distortion + AmpSimulator.
0: Gain (0 to 127) – Adjusts the input gain.
1: Low (0 to 127) – Adjusts the low-band gain. The cutoff frequency differs
according to the preset DSP.
2: High (0 to 127) – Adjusts the high-band gain. The cutoff frequency differs
according to the preset DSP.
3: Level (0 to 127) – Adjusts the output level.