Filter
Top Products
44
Chapter 4 Other Functions
Changing the Equalizer
Settings
You can make fine, detailed changes to the equalizer settings.
1.
Switch to Function mode (p. 38), and press the
[Equalizer] button.
2.
Hold down the [Equalizer] button, and press the
[-] or [+] button to select item.
3.
Press the [-] or [+] button to change the settings.
* Sounds may become distorted as the Gain level increases.
→
The equalizer is switched on whenever the settings are
changed.
→
The FP-2 remembers the settings even while its power is
turned off.
Connecting to Audio
Equipment
You can connect audio devices to play the sound of the FP-2
through the speakers of your audio system, or to record your
performance on a tape recorder or other recording device.
When connecting, please use an audio cable with a standard
phone plug (sold separately).
Connection Examples
* To prevent malfunction and/or damage to speakers or other
devices, always turn down the volume, and turn off the power
on all devices before making any connections.
Playing the sound of the FP-2 through the speakers
of an audio system/Recording the performance of
the FP-2 on a recording device
fig.audio1.e
❍
Use the following procedure when turning on the power.
1.
Set the volume of the FP-2 and of the connected
devices to the minimum position.
2.
Set the speaker switch to “Off” located on the rear
panel.
3.
Turn on the power of the FP-2.
4.
Turn on the power of the connected device.
5.
Adjust the volume of each device.
Param
eter
Indi-
cation
Value Description
Low
Gain
Lo.G
-12–+12dB Adjusts the level of the low-
frequency range.
Low
Freq
Lo.f
100, 200, 400
(Hz)
Frequency point in the low-
frequency range. Generally,
this changes the level at and
below this frequency.
Low
Mid
Gain
Lm.G
-12–+12dB Adjusts the level of the low-
frequency range to
midrange.
Low
Mid
Freq
Lm.F
200, 250, 315,
400, 500, 630,
800, 1.00, 1.25,
1.60, 2.00, 2.50,
3.15, 4.00, 5.00,
6.30, 8.00
Frequency point in the low-
frequency range to
midrange. This changes the
level of the specified band-
width centered on this fre-
quency.
Low
Mid
Q
Lm.q
0.5, 1.0, 2.0,
4.0, 8.0
Changes the bandwidth of
the low-frequency range to
midrange. The bandwidth
affected by the controls nar-
rows as the value increases.
High
Mid
Gain
Hm.G
-12–+12dB Adjusts the level of the mid-
to high-frequency range.
High
Mid
Freq
Hm.F
200, 250, 315,
400, 500, 630,
800, 1.00, 1.25,
1.60, 2.00, 2.50,
3.15, 4.00, 5.00,
6.30, 8.00
Frequency point in the mid-
to high-frequency range to
midrange. This changes the
level of the specified band-
width centered on this fre-
quency.
High
Mid
Q
Hm.q
0.5, 1.0, 2.0,
4.0, 8.0
Changes the bandwidth of
the mid- to high-frequency
range. The bandwidth
affected by the controls nar-
rows as the value increases.
High
Gain
Hi.G
-12–+12dB Adjusts the level of the high-
frequency range.
High
Freq
Hi.F
2.00, 4.00, 8.00
(KHz)
Frequency point in the high-
frequency range. Generally,
this changes the level at and
over this frequency.
Param
eter
Indi-
cation
Value Description
FP-2
Input R/L
(Line In, Aux In)
FP-2_e.book 44 ページ ２００４年１１月２６日 金曜日 午後４時２５分