Filter
Top Products
Table of Figures
TASCAM DM-3200 Automation Guide 3
1 – Introduction
Figure 1.1: Timecode source selection (showing USB MTC selected) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2 – Starting out with the timecode
Figure 2.1: The automation FILES display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Figure 2.2: Automation SETUP screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Figure 2.3: Naming a mix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3 – Automation overview
Figure 3.1: Illustration of trim mode behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Figure 3.2: AUTO SETUP screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Figure 3.3: AUTO FILES screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Figure 3.4: AUTO CONFIG display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4 – Operation
Figure 4.1: Writing a fader move over a previous static fader position with Auto Revert enabled . . . . . . . . . . . . 17
Figure 4.2: Writing a POD (or encoder) move over a previous static position with Auto Revert enabled . . . . . . . . 17
Figure 4.3: Writing a new fader move over a previous Dynamic fader move with Auto Revert enabled . . . . . . . . 18
Figure 4.4: Writing a new POD (or encoder) move over a previous Dynamic move with
Auto Revert enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Figure 4.5: Writing a new fader move over a previous Static fader position with Auto Revert disabled . . . . . . . . 19
Figure 4.6: Writing a new POD or encoder move over a previous Static position with Auto Revert disabled . . . . 19
Figure 4.7: Writing a new fader move over previous Dynamic fader moves with Auto Revert disabled . . . . . . . . 20
Figure 4.8: Writing a new POD or encoder move over previous Dynamic moves with Auto Revert disabled . . . . . 20
Figure 4.9: Write to End over previous Static fader position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 4.10: Write to End over previous Dynamic fader moves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 4.11: Write to End over previous Static POD or encoder position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Figure 4.12: Write to End over previous Dynamic POD or encoder moves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Figure 4.13: Writing new switch events over previous switch events with Auto Revert enabled . . . . . . . . . . . . . . 24
Figure 4.14: Writing new switch events over previous switch events with Auto Revert disabled . . . . . . . . . . . . . 25
Figure 4.15: Writing a new switch event with Write to End enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Figure 4.16: Trimming fader moves with Auto Revert enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Figure 4.17: Trimming POD and encoder moves with Auto Revert enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Figure 4.18: Trimming fader moves with Auto Revert disabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Figure 4.19: Trimming POD and encoder moves with Auto Revert disabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Figure 4.20: Trimming fader moves with Trim to End enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Figure 4.21: Trimming POD and encoder moves with Trim to End enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Figure 4.22: Initial status and dynamic data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Figure 4.23: Initial Status editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33