Filter
Top Products
PM5D/PM5D-RH V2 / DSP5D Owner’s Manual Reference section 189
Information shown
in the display
Function
menu
Global
functions
Output
functions
Input
functions
Appendices
BANK ON/OFF
If this button is on, bank select messages will be trans-
mitted and received in Single mode (this is
unavailable in Multi mode).
MULTI
If this button is on, program changes will be trans-
mitted/received on multiple MIDI channels (Multi
mode).
Hint
• If program change reception is on, the PM5D’s scenes or
effects will switch when the appropriate program change is
received from an external device. Additionally, if transmis-
sion is on, program changes will be transmitted to an
external device when scenes or effects are switched on the
PM5D.
• The scene/effect assignment for each program change num-
ber is made in the MIDI PGM CHANGE screen (
➥
p.190).
• CONTROL CHANGE MODE
In this area you can select the control change transmis-
sion/reception method.
NRPN
If this button is on, PM5D mix parameters will be
transmitted/received as NRPN messages.
TABLE [SINGLE]
If this button is on, PM5D mix parameters will be
transmitted/received as control change messages on a
single MIDI channel.
TABLE [MULTI]
If this button is on, PM5D mix parameters will be
transmitted/received as control change messages on
multiple MIDI channels.
Hint
• If control change reception is on, the PM5D’s parameters
will change when the appropriate control change is received
from an external device. If transmission is on, a control
change will be transmitted to an external device when you
edit a parameter on the PM5D.
• If NRPN is selected as the control change mode, the assign-
ment of parameters to NRPN is pre-defined and cannot be
changed.
• If TABLE [SINGLE] or TABLE [MULTI] is selected as the
control change mode, the parameter assignment for each
control number can be edited in the MIDI CTRL CHANGE
screen (
➥
p.191).
B Tx (MIDI transmission)
Here you can make various settings for transmission of
MIDI messages.
• MIDI PORT Tx (MIDI transmission port)
Select the port at which the PM5D will transmit MIDI
messages. You have the following choices.
MIDI . . . . . . . The rear panel MIDI IN connector
USB . . . . . . . .The rear panel USB connector
SLOT 1–4 . . .A card that supports serial transmis-
sion and is installed in rear panel slot
1–4
Move the cursor to this box and turn the [DATA]
encoder or click the / buttons at left or right to
change the setting; then press the [ENTER] key to
finalize the change.
If you select USB or SLOT 1–4, you will need to spec-
ify the port number (1–8) in the field on the right
(Depending on the card that is installed, some slots
may have only one port.)
• SINGLE MODE MIDI CH Tx (MIDI transmission
channel for Single mode)
Select the MIDI channel on which the PM5D will
transmit program changes, control changes, parameter
changes, and bulk data. (This setting is valid only in
Single mode.) Move the cursor to this box and turn the
[DATA] encoder or click the / buttons at left or
right to change the setting; then press the [ENTER] key
to finalize the change.
• PROGRAM CHANGE Tx (Program change
transmission)
• CONTROL CHANGE Tx (Control change
transmission)
• PARAMETER CHANGE Tx (Parameter change
transmission)
These buttons turn transmission on/off for program
changes, control changes, and parameter changes
respectively.
Hint
Parameter changes are a method by which PM5D parame-
ters are transmitted in the form of system exclusive
messages.
• MIDI THRU Tx (Thru output)
Select the port from which messages input to MIDI
THRU Rx will be output. The selection method is the
same as for MIDI PORT Tx.
C Rx (MIDI reception)
Here you can make various settings for reception of
MIDI messages.
• MIDI PORT Rx (MIDI reception port)
Select the port from which the PM5D will receive
MIDI messages.
• SINGLE MODE MIDI CH Rx (MIDI reception chan-
nel for Single mode)
Select the MIDI channel on which the PM5D will
receive program changes, control changes, parameter
changes, and bulk data. (This setting is valid only in
Single mode.)
• PROGRAM CHANGE Rx (Program change
reception)
• CONTROL CHANGE Rx (Control change
reception)
• PARAMETER CHANGE Rx (Parameter change
reception)
These buttons turn transmission on/off for program
changes, control changes, and parameter changes
respectively.
• MIDI THRU Rx (Thru input)
Here you can select the port that will “thru input” the
received MIDI messages.
D ECHO (MIDI message echo output)
Here you can select whether received program changes,
control changes, parameter changes, and other MIDI
messages will be echoed out from the MIDI transmis-
sion port.