ICP-CC404 | Installation Guide | 11.0 Dialer Information
48 Bosch Security Systems, Inc. | 12/08 | F01U089401-02
When using Domestic Dialing Format, the number of
identification beeps is determined by the value
programmed in Location 039 (Receiver 1) and
Location 079 (Receiver 2). This value allows the
identification of up to 15 different control panels that
call the same telephone number.
Example
To program the Subscriber ID Number as 4729,
program:
0 0 4 7 2 9
11.6 Dialing Format
Program the Dialing Format in Location 080.
The default value for the Dialing Format is 1.
The Dialing Format determines the method for
dialing telephone numbers. The options are:
1 – Australian DTMF (5 digits/sec)
2 – Australian decadic
3 – Alternate DTMF and Australian decadic
4 – International DTMF (touch tone)
5 – Reversed decadic (10 minus 1)
6 – Alternate DTMF and reversed decadic
Options 3 and 6 alternate the dialing sequence
between DTMF and decadic if the call to the base
station receiver is unsuccessful. Use caution when
selecting the dialing method.
Select the Australian method only if the control panel
is connected to the Australian Telecommunications
Network. Select the International DTMF dialing
option only in countries that allow both the caller and
the receiver to terminate a phone call. Using the
incorrect format can disable the control panel’s
patented Telephone Anti-Jamming feature.
The alternating sequence is: DTMF –
decadic – DTMF – decadic – DTMF –
decadic.
11.7 Telco Arming Sequence
Program the Telco Arming Sequence in Locations 113
to 142.
The default value for the Telco Arming Sequence is
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0.
These locations allow you to activate call diversion
automatically on your telephone when you arm the
system in AWAY Mode. Refer to Table 39.
Table 39: Telco Arm or Disarm Dialing Digits
Digit
Required
Number to
Program
Digit
Required
Number to
Program
terminator 0 8 8
1 1 9 9
2 2 0 10
3 3 * 11
4 4 # 12
5 5 4 sec pause 13
6 6 break 14
7 7
When the Telco Arming Sequence is activated after
arming the system in AWAY Mode, the control panel
redirects all calls to your mobile phone, pocket pager,
or answering service.
Contact your telecommunications provider for more
information on Call Forward operations.
To turn call forward (immediate) on, enter:
[* 2 1][forwarding telephone number][#]
Example
To immediately forward all incoming calls to the
telephone number 96721055 after arming the system
in AWAY Mode, program:
[11 2 1 9 6 7 2 1 10 5 5 12 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0]
To turn call forward (no answer) on, enter:
[* 6 1][forwarding telephone number][#]
Example
To forward all incoming calls, when there is no
answer, to the telephone number 96721055 after
arming the system in AWAY Mode, program:
[11 6 1 9 6 7 2 1 10 5 5 12 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0]
11.8 Telco Disarming Sequence
Program the Telco Disarming Sequence in
Locations 143 to 158.
The default value for the Telco Disarming Sequence
is 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0.
This parameter allows you to deactivate call diversion
automatically on your telephone when you disarm the
system from AWAY Mode. Refer to Table 39.
To turn call forward (immediate) off, enter:
[# 2 1 #]
Example
To disable call forward (immediate) after disarming
the system from AWAY Mode, program:
[12 2 1 12 0 0 0 0 0 0 0 0 0 0 0 0]
