Filter
Top Products
23 DIGITAL PRO MIXER DDM4000 User Manual
Press the BANK ASSIGN push button to select the memory bank that is 1)
to be processed with the eect.
Select the length of the brake by continuously pressing the SELECT 2)
push button (64). This is shown on the display.
Press the SMP FX ON push button 3) (63) to activate the eect.
The push button ashes.
When the sampler comes to an end (SMP FX ON push button and PLAY/OUT push
button of the selected bank ash), the sampler-eect needs to be deactivated
by pressing SMP FX ON again in order to restart playback.
Press the SMP FX ON push button to restart playback.4)
Further 6. Settings
Loading factory settings6.1
Press the LOAD push button 1) (35). The display switches to “User Setup”.
The LOAD push button lights up.
Select the factory preset by turning and pressing the left 2)
PARAMETER knob (45).
Press the left PARAMETER knob to conrm the selection.3)
Press the LOAD push button 4) (35) or the ESC push button (52)
to exit User Setup.
Output setup6.2
Press the CONSOLE SETUP knob 1) (51) for approximately 2 seconds.
Select “Output Setup” by turning and pressing the CONSOLE SETUP knob. 2)
Output Setup appears on the display:
In Output Setup, you make the following settings:
Mono:
Use this function to switch the OUT B outputs (74) to mono.
Turn the left PARAMETER knob 1) (45) to select OFF or ON.
Press the left PARAMETER knob to conrm.2)
MODE:
You can use Output A (73) together with the Subwoofer output, in which case
the bass frequencies are separated from the Main output (crossover function).
FULL-FREQ: MAIN OUT A (73) emits the entire frequency
spectrum (including the bass signal).
The Subwoofer output gives out the
subwoofer signal.
CROSSOVER: The Subwoofer output gives out the subwoofer
signal. MAIN OUT A emits frequencies that are
above the crossover frequency.
Turn the CONSOLE SETUP knob 1) (51) to select the mode
(FULL-FREQ, CROSSOVER).
Press the CONSOLE SETUP knob to conrm.2)
SUB OUT:
The following are used to adjust the crossover frequency and output level
of the subwoofer output.
FREQ: Crossover frequency between SUB OUT and MAIN OUT
GAIN: Output level of SUB OUT
TAPE / S/PDIF:
The levels of both Tape and S/PDIF outputs can be adjusted individually.
Press the right PARAMETER knob to select the parameter 1)
(FREQ, GAIN or TAPE/ S/PDIF GAIN).
Turn the PARAMETER knob to change the value.2)
Press the ESC push button to exit Output Setup.3)
Adjusting display contrast6.3
Press the LOAD push button 1) (35). User Setup appears on the display.
Turn the right PARAMETER knob 2) (45) to change the con-trast.
Press the LOAD push button to exit User Setup.3)
The DDM4000 as MIDI 7. Controller
The DDM4000 can be used to control DJ or sequencer software applications
by converting individual mixer sections on the mixer to MIDI controllers
and assigning these to dened software functions. The MIDI interface
(76) is used to transmit the data. To connect to the mixer, the computer
requires a MIDI interface, which can be purchased as USB alternative for a
very reasonable price.
USB-MIDI Interface*
MIDI IN/OUT/THRU
Laptop
* not included
Fig. 7.1: Connecting the DDM4000 to a computer
OUTPUT
SETUP
SUB-OUTS/PDIF
TAPE/
MONO
OFF
ON
MODE
FREQ GAIN GAIN
FULL-FREQ
CROSSOVER
-6.0dB-3.0dB55Hz
OUT B