Filter
Top Products
57
Control 2 values when OSC 1 Wave = DWGS
When the synth parameter OSC 1 "WAVE" is set to DWGS, the "CONTROL 2" (knob 3 )
will select the DWGS waveform. The value of the control change transmitted/received
by operating the "CONTROL 2" (knob 3 ) corresponds to the parameter value as
follows.
0, 1 1
2, 3 2
4, 5 3
6, 7 4
8, 9 5
10, 11 6
12, 13 7
14, 15 8
16, 17 9
18, 19 10
20, 21 11
22, 23 12
24, 25 13
26, 27 14
28, 29 15
30, 31 16
32, 33 17
34, 35 18
36, 37 19
38, 39 20
40, 41 21
42, 43 22
44, 45 23
46, 47 24
48, 49 25
50, 51 26
52, 53 27
54, 55 28
56, 57 29
58, 59 30
60, 61 31
62, 63 32
Value
(transmitted, received)
Value
(transmitted, received)
DWGS Wave
DWGS Wave
64, 65 33
66, 67 34
68, 69 35
70, 71 36
72, 73 37
74, 75 38
76, 77 39
78, 79 40
80, 81 41
82, 83 42
84, 85 43
86, 87 44
88, 89 45
90, 91 46
92, 93 47
94, 95 48
96, 97 49
98, 99 50
100, 101 51
102, 103 52
104, 105 53
106, 107 54
108, 109 55
110, 111 56
112, 113 57
114, 115 58
116, 117 59
118, 119 60
120, 121 61
122, 123 62
124, 125 63
126, 127 64
Messages transmitted and received by the microKORG
OSC 2 Semitone values
The value of the control change transmitted/received by operating OSC 2
"SEMITONE" (knob 3 ) of a synth program corresponds to the parameter value as
follows.
0...2 –24
3...5 –23
6, 7 –22
8...10 –21
11...13 –20
14, 15 –19
16...18 –18
19, 20 –17
21...23 –16
24...26 –15
27, 28 –14
29...31 –13
32, 33 –12
34...36 –11
37...39 –10
40, 41 –9
42...44 –8
45...47 –7
48, 49 –6
50...52 –5
53, 54 –4
55...57 –3
58...60 –2
61, 62 –1
63...65 0
Value
(transmitted, received)
OSC 2 Semitone
Value
(transmitted, received)
OSC 2 Semitone
66, 67 +1
68...70 +2
71...73 +3
74, 75 +4
76...78 +5
79, 80 +6
81...83 +7
84...86 +8
87, 88 +9
89...91 +10
92...94 +11
95, 96 +12
97...99 +13
100, 101 +14
102...104 +15
105...107 +16
108, 109 +17
110...112 +18
113, 114 +19
115...117 +20
118...120 +21
121, 122 +22
123...125 +23
126, 127 +24
"SYNC NOTE" value when LFO 1/2 or DELAY "TEMPO SYNC" = ON
If "TEMPO SYNC" is ON, the parameter that is set by the LFO 1/2 "FREQUENCY"
(knob 4 ) or the DELAY "DELAY TIME" (knob 3 ) will change to "SYNC NOTE." In this
case, the value of the control change message transmitted by knob operations (or
received) will correspond to the parameter value as shown below.
0...8 1/1 1/32
9...17 3/4 1/24
18...25 2/3 1/16
26...34 1/2 1/12
35...42 3/8 3/32
43...51 1/3 1/8
52...59 1/4 1/6
60...68 3/16 3/16
69...76 1/6 1/4
77...85 1/8 1/3
86...93 3/32 3/8
94...102 1/12 1/2
103...110 1/16 2/3
111...119 1/24 3/4
120...127 1/32 1/1
LFO Sync Note
DELAY Sync Note
Value
(transmitted, received)