Filter
Top Products
119
Performance Mode
Part (Settings for each Part)
You can edit each Part in a Performance. Use Knob [A]
to select the Part, then set its parameters. The
following six screens are available, though their
contents will vary according to the Part selected.
• Part Mixer
• Part Tone
• Part Layer
• Part Receive switch
• Part Controller
• Part Insertion Effect
Part Mixer
You can set various Voice output parameters for each
Part. The following two screens are available.
MIX Vce (Mix Voice)
MIX Level
The MIX Vce (Mix Voice) screen will change to the Mix
Template screen if PartAD (A/D Input Part) has been
selected.
MIX Vce/Template
(Mix Voice/Template)
You can assign a Voice/Template to each Part. Use
Knob [A] to select the Part, then set its Voice/Template
parameters. The display will vary as follows according
to the Part selected.
• If Part01 to Part16 has been selected
You can use the same method as the Category Search
(Page 67) to set the Voice.
■ Memory (Voice Memory)
❏ Settings:
PRE1 (Preset 1), PRE2 (Preset 2), INT (Internal Normal),
EXT (External Normal), PRE (Preset Drum), INT
(Internal Drum), EXT (External Drum)
■ Number (Program Number)
❏ Settings:
1 ~ 128 (for Normal Voices), DR1 ~ DR8 (for Preset
Drum), DR1 ~ DR2 (for Internal/External Drum)
Details about Categories are given in the Category List
on Page 70.
• If PartP1/PartP2 (Plug-in 1/2)
has been selected
Set the Voice for the Plug-in 1/2 Part. This screen is
only displayed if a Plug-in Board has been installed.
Use Knob [B] to select PLG1/2INT (internal memory)
MIXíVce) Memory Number Ctgry Search
Part01 PRE1:128(H16)[Pf:GrandPiano]
and the MSB/LSB (Plug-in Board’s Bank), and use
Knob [C] to select the Program Number.
■ Bank
❏ Settings:
PartP1/P2 (Plug-in 1/2): PLG1/2 INT (Plug-in 1/2
Internal), MSB/LSB (Plug-in Bank)
For details about Plug-in Banks (Bank Select
MSB/LSB), refer to the Owner’s Manual that came with
your Plug-in Board.
■ Number (Program Number)
❏ Settings:
PLG1/2 INT (Plug-in 1/2 Internal): 1 ~ 64
MSB/LSB (Plug-in Bank): 1 ~ 128
There may be a delay when changing programs for Plug-in
Parts (since voice data and default settings need to be sent).
To change Voices for Plug-in Parts in a song, you should
insert the Program Changes in the less data-intensive areas
of the song. When selecting a Plug-in Board Voice, you
should use the Program Number of the Parameter Change
(multi-part). Details are given in the Owner’s Manual that
comes with the Plug-in Board.
In Performance Mode, the Part assignments for Plug-in
Boards are fixed at “16” for PLG1 and “15” for PLG2.
For details about Plug-in Voices, refer to the Owner’s
Manual that came with your Plug-in Board.
• If Part17 to Part32 has been selected
You can set Voices for Parts 17 to 32 if you have a
multitimbral Plug-in board installed. Use Knob [B] to
select the Voice Bank and Knob [C] to select the
Program Number.
■ Bank/Number (Bank/Program Number)
❏ Settings: Refer to the Owner’s Manual that came with the
Plug-in board.
This setting is only held temporarily and cannot be
stored with the Performance.
• If PartAD (A/D Input Part) has
been selected
An audio source connected to the A/D INPUT jack can
be used as a Part. There are 13 different templates for
Effect Type and Gain settings. Select the A/D Input
Part source and the template.
MIXíTemplate)Src Number
PartAD keybaord --[InsEF off ]
MIXíVce) Bank Number
Part17 NORM/001:001(A01)[Pf:GrandPno]
MIXíVce) Bank Number Ctgry Search
PartP1 NORM/001:128(H16)[Pf:GrandPiano]