Filter
Top Products
59
Basics
Section
4Select one of “Zone01” to “Zone04” using the
Knob [A]. As we have selected “4zone” for the
Mode parameter, you can now select setting
screens for four Zones. Select “Zone01” to get
started with the settings.
You can also use the BANK [A] to [D] keys to
respectively select “Zone01” to “Zone04.”
Selecting a Zone opens the MKB Transmit
page. You may want to select a sub screen to
set up a Zone using the [PAGE] knob. But you
first specify basic items in the MKB Transmit
page, such as MIDI transmit channel, enabling
or disabling MIDI output to the internal tone
generator and to the MIDI OUT connector.
5Set MIDI transmit channel (TrnsCh) to “Ch01”
using the Knob [C]. Set MIDI output to the
internal tone generator (TG) and MIDI OUT
(MIDI) both to “on.”
These settings can differentiate each Zone from
one another, to internally or externally output
performance made in each Zone using a
separate MIDI channel. Finally, you will
separately control sound tones from four zones.
To do this, set “Ch01” to “Ch04” respectively to
the “TrnsCh” parameters in the MKB Transmit
pages for Zones 1 to 4. For the “TG” and
“MIDI” parameters, set both “on” for Zones 1
to 3. For Zone 4, set “off” to “TG” and “on” to
“MIDI.” You can switch between multiple
MKB Transmit screens using the Knob [A].
Some of basic settings for four zones are now
complete.
6Select “Zone01” again using the Knob [A].
Open the MKB Note screen using the [PAGE]
knob. In this screen, you can specify a key
range for a Zone.
In the MKB Note page, you can also find other
parameters such as Note Limit, Transpose, etc.
Refer to page 128 for more information about
these parameters.
7Set “Note Limit” (zone key range) with the
lowest and highest notes using Knobs [1]
(lowest) and [2] (highest). For “Zone01”, select
“C-2” for the lowest note and “B1” for the
highest.
8Use the Knob [A] to switch to the MKB Note
page for “Zone02”. As in the same manner in
step 7, select “C2” for the lowest note and
“B2” for the highest.
MKBíNote)Octave Transpose Note Limit
Zone01 +1 +11 C-2 - G 8
MKBíTransmit) TrnsCh TG MIDI
Zone01 Ch01 on on
9Use again the Knob [A] to switch to the MKB
Note screen for “Zone03”. As in the same
manner in step 7, select “C3” for the lowest
note and “G8” for the highest.
)Use the Knob one more time [A] to switch to
the MKB Note page for “Zone04”. As in the
same manner in step 7, select “C3” for the
lowest note and “G8” for the highest. Note
that this key range setting will make a
overlapped range with Zone 3.
For detailed settings of a Zone, refer to page 127.
!Turn the Knob [A] and select a Part for a Zone.
In this example, we select Part 1 for Zone 1,
Part 2 and Part 3 respectively for Zone 2 and
Zone 3. We don’t select any internal Part for
Zone 4 since Zone 4 is set only to output
performance information via MIDI Out. First,
select Part 1 (Part01) for Zone 1.
You can also use the [MEMORY] or
PROGRAM/PART keys to select a Part for a
Zone (page 109).
@Use the [PAGE] knob and open the MIX Vce
screen, to set up a Voice for performance using
the Arpeggiator.
#Use the [PAGE] knob and open the Layer Mode
(LYR Mode) screen. Set the Arpeggiator
Switch (Arp) to “on,” Layer Switch (Layer) to
“off,” and MIDI receive channel (RcvCh) to
“1.” Finally in the Arpeggio type (ARP Type)
screen, set the Switch parameter to “on.”
Prepare basic Arpeggiator settings (Type, etc.) in
Voice Edit Mode before you set up a Zone setting
in Performance Edit Mode.
With settings made in steps ! to #, you can
now play the Arpeggiator with a Voice assigned
to “Part01” (Part 1) set to MIDI receive
channel 1 (RcvCh) when you play in the key
range of Zone 1.
$As in the same manner in steps ! to #, set up for
Zone 2. Turn the Knob [A] and select “Part02”.
Next go to the Mix Voice (MIX Vce) screen using
the [PAGE] knob, and select a Voice for the bass
sound. Then, use the [PAGE] knob to open the
Layer Mode (LYR Mode) screen and set MIDI
receive channel (RcvCh) to “2”.
With settings made here, you can now play with
the bass sound using a Voice assigned to
“Part02” set to MIDI receive channel 2 (RcvCh)
when you play in the key range of Zone 2.
LYRíMode) Mode Arp Layer RcvCh
Part01 Poly on off 1
MIXíVce) Memory Number Ctgry Search
Part01 PRE1:001(A01)[Pf:StereoGrnd]