Filter
Top Products
120
Performance Mode
■ Src (Source)
Select the source connected to the A/D INPUT jack.
❏ Settings: mic (microphone), guitar, keyboard, audio
■ Number (Template Number)
Select the Template Number. You can choose from
13 templates for each source.
❏ Settings: 0 ~ 12
If you attempt to select a Number from within “5” to “12”
while you have a setting other than “PartAD” for the
Insert Effect (Ins EF) parameter in the Effect Part (EFF
Part) page, it will be disabled with “InsEF off” shown for
the Number parameter.
MIX Level
You can set output level, pan, effect send and other
parameters for each Part. This is useful when setting
up the levels of each Part in a mix.
■ Vol (Volume)
Set the output level of the Part.
❏ Settings: 0 ~ 127
■ Pan
Set the stereo pan position of the Part.
❏ Settings: L63 (Left) ~ C (Center) ~ R63 (Right)
MIXíLevel) Vol Pan RevSend ChoSend
Part01 127 C 64 0
MIC
GUITAR
KEYBOARD
AUDIO
PresetName
InputGain
VariType
PresetName
InputGain
VariType
PresetName
InputGain
VariType
PresetName
InputGain
VariType
0
Off
mic
-
Off
mic
-
Off
line
-
Off
line
-
1
Mic
mic
-
Guitar
mic
-
Keyboard
line
-
Audio
line
-
2
Reverb
mic
-
Reverb
mic
-
Reverb
line
-
Reverb
line
-
3
Chorus
mic
-
Chorus
mic
-
Chorus
line
-
Chorus
line
-
4
Cho+Rev
mic
-
Cho+Rev
mic
-
Cho+Rev
line
-
Cho+Rev
line
-
5
Karaoke1
mic
Karaoke1
Tube
mic
AmpSim.
PhaserEP
line
Phaser1
Audio
line
-
6
Karaoke2
mic
Karaoke2
Stack
mic
AmpSim.
PanEP
line
AutoPan
Audio
line
-
MIC
GUITAR
KEYBOARD
AUDIO
PresetName
InputGain
VariType
PresetName
InputGain
VariType
PresetName
InputGain
VariType
PresetName
InputGain
VariType
7
Karaoke3
mic
Karaoke3
FlangGtr
mic
Flanger1
WahClavi
line
TouchWah1
Audio
line
-
8
Echo
mic
Echo
CleanGtr
mic
Celeste3
RotaryOrg
line
RotarySp.
Audio
line
-
9
Vocal
mic
Stage1
FuncGtr
mic
TouchWah2
SynthStr
line
Symphonic
Audio
line
-
10
Studio
mic
Exciter
Tremolo
mic
Tremolo
SynthPad
line
Flanger2
Audio
line
-
11
OctUp
mic
PitChange1
Phaser
mic
Phaser1
SynthLead
line
DelayLCR
Audio
line
-
12
OctDown
mic
PitChange1
5thGuitar
mic
PitChange1
SFX
line
PitChange1
Audio
line
-
Number
Src
Number
Src
■ RevSend (Reverb Send)
Set the Send level of the signal sent from Insertion
Effect 1/2 (or the bypassed signal) to the Reverb
effect.
❏ Settings: 0 ~ 127
■ ChoSend (Chorus Send)
Set the Send level of the signal sent from Insertion
Effect 1/2 (or the bypassed signal) to the Chorus
effect.
❏ Settings: 0 ~ 127
Part Tone
You can set Filter, Envelope Generator and other
parameters controlling the tonal characteristics of each
Part. The following four screens are available.
TON Filter (Tone Filter)
TON EG (Tone Envelope Generator)
TON Portamento (Tone Portamento)
TON Other (Tone Other)
TON Filter (Tone Filter)
You can use filters to adjust the tone of each Part. If
the filter is an LPF and HPF combination, the Cutoff
parameter applies to the LPF. These parameters are
also available in the Common Quick Edit screens.
This screen is not available for the A/D Input Part.
Details about the Filter are given on Page 83.
■ Cutoff
Raise or lower the Cutoff frequency for each
Element of a Part.
For each Element, if a combined Low Pass and High
Pass Filter is being used, this parameter adjusts the
Cutoff frequency of the Low Pass Filter.
❏ Settings: -64 ~ 0 ~ +63
■ Reso (Resonance)
Set the amount of Resonance (harmonic emphasis)
applied to the signal at the Cutoff frequency. This
adds further character to the sound.
❏ Settings: -64 ~ 0 ~ +63
TONíFilter) Cutoff Reso
Part01 +63 +63