Filter
Top Products
70
Effects List
Specifications for each Speaker Type
The speaker column indicates the diameter of each speaker unit (in
inches) and the number of units.
Flattens out high levels and boosts low levels, smoothing out
fluctuations in volume.
fig.MFX-40
Compresses signals that exceed a specified volume level, preventing
distortion from occurring.
fig.MFX-41
Cuts the reverb’s delay according to the volume of the sound sent into
the effect. Use this when you want to create an artificial-sounding
decrease in the reverb’s decay.
fig.MFX-42
Type
Cabinet
Speak-
er
Micro-
phone
SMALL 1
small open-back enclosure 10 dynamic
SMALL 2
small open-back enclosure 10 dynamic
MIDDLE
open back enclosure 12 x 1 dynamic
JC-120
open back enclosure 12 x 2 dynamic
BUILT-IN 1
open back enclosure
12 x 2 dynamic
BUILT-IN 2
open back enclosure
12 x 2 condenser
BUILT-IN 3
open back enclosure
12 x 2 condenser
BUILT-IN 4
open back enclosure
12 x 2 condenser
BUILT-IN 5
open back enclosure
12 x 2 condenser
BG STACK 1
sealed enclosure
12 x 2 condenser
BG STACK 2
large sealed enclosure
12 x 2 condenser
MS STACK 1
large sealed enclosure
12 x 4 condenser
MS STACK 2
large sealed enclosure
12 x 4 condenser
METAL STACK
large double stack
12 x 4 condenser
2-STACK
large double stack
12 x 4 condenser
3-STACK
large triple stack
12 x 4 condenser
40:
COMPRESSOR
Parameter
Value Description
Attack
0–127
Sets the speed at which compression starts
Threshold
0–127
Adjusts the volume at which compression
begins
Post Gain
0– +18 dB
Adjusts the output gain.
Low Gain
-15– +15 dB
Gain of the low frequency range
High Gain
-15– +15 dB
Gain of the high frequency range
Level
0–127
Output level
L in
R in
L out
R out
Compressor
2-Band EQ
2-Band EQ
Compressor
41: LIMITER
Parameter
Value Description
Release
0–127
Adjusts the time after the signal volume falls
below the Threshold Level until compression
is no longer applied.
Threshold
0–127
Adjusts the volume at which compression
begins
Ratio
1.5:1, 2:1,
4:1,
100:1
Compression ratio
Post Gain
0– +18 dB
Adjusts the output gain.
Low Gain
-15– +15 dB
Gain of the low frequency range
High Gain
-15– +15 dB
Gain of the high frequency range
Level
0–127
Output level
42:
GATE
Parameter
Value Description
Threshold
0–127
Volume level at which the gate begins to close
Mode
GATE,
DUCK
Type of gate
GATE:
The gate will close when the vol-
ume of the original sound decreases, cut-
ting the original sound.
DUCK (Ducking):
The gate will close when
the volume of the original sound increas-
es, cutting the original sound.
Attack
0–127
Adjusts the time it takes for the gate to fully
open after being triggered.
Hold
0–127
Adjusts the time it takes for the gate to start
closing after the source sound falls beneath
the Threshold.
Release
0–127
Adjusts the time it takes the gate to fully
close after the hold time.
Balance
D100:0W–
D0:100W
Volume balance between the direct sound
(D) and the effect sound (W)
Level
0–127 Output level
L in
R in
L out
R out
Limiter
2-Band EQ
2-Band EQ
Limiter
L in
R in
L out
R out
Gate
Gate
GW-8_e.book 70 ページ ２００８年４月１日 火曜日 午前１１時４４分