Filter
Top Products
77
Effects List
Shifts the pitch of the original sound. This 2-voice pitch shifter has two
pitch shifters, and can add two pitch shifted sounds to the original
sound.
fig.MFX-62
A pitch shifter in which the amount of pitch shift is varied by a 16-step
sequence.
fig.MFX-63
Adds reverberation to the sound, simulating an acoustic space.
fig.MFX-64
62: 2VOI PITCH SHIFTER (2VOICE PITCH SHIFTER)
Parameter
Value Description
Pitch 1:
Coarse
-24-+12 semi
Adjusts the pitch of Pitch Shift 1
in semitone steps.
Pitch 1:Fine
-100-+100 cent
Adjusts the pitch of Pitch Shift
Pitch 1 in 2-cent steps.
Pitch 1:Delay
0–1300 ms, note
Adjusts the delay time from the
direct sound until the Pitch Shift 1
sound is heard.
Pitch 1:Feedback
-98– +98%
Adjusts the proportion of the
pitch shifted sound that is fed
back into the effect. Negative (-)
settings will invert the phase.
Pitch 1:Pan
L64-63R
Stereo location of the Pitch Shift
1 sound
Pitch 1:Level
0–127
Volume of the Pitch Shift1 sound
Pitch 2:
Coarse
-24-+12 semi
Settings of the Pitch Shift 2
sound.
The parameters are the same as
for the Pitch Shift 1 sound.
Pitch 2:Fine
-100-+100 cent
Pitch 2:Delay
0–1300 ms, note
Pitch 2:Feedback
-98– +98%
Pitch 2:Pan
L64-63R
Pitch 2:Level
0–127
Low Gain
-15– +15 dB Gain of the low range
High Gain
-15– +15 dB Gain of the high range
Level Balance
A100:0B-A0:100B
Volume balance between the
Pitch Shift 1 and Pitch Shift 2
sounds
Balance
D100:0W-D0:100W
Volume balance between the di-
rect sound (D) and the pitch shift-
ed sound (W)
Level
0-127
Output Level
63:
STEP PITCH SHIFTER
Parameter
Range Explanation
Step 01–16
-24–+12 semi
Amount of pitch shift at each step
(semitone units)
Rate
0.05–10.00 Hz, note
Rate at which the 16-step se-
quence will cycle
L in
R in
L out
R out
2Voice Pitch Shifter
Level 1
Balance W
Balance D
Balance W
Balance D
Level 1
Pan 2 R
Pan 1 L
Pan 1 R
Pan 2 L
L in
R in
Step Pitch Shifter
Step Pitch Shifter
L out
R out
2-Band
EQ
2-Band
EQ
Attack
0–127
Speed at which the amount of
pitch shift changes between steps
Gate Time
0–127
Duration of the pitch shifted
sound at each step
Fine
-100– +100 cent
Pitch shift adjustment for all steps
(2-cent units)
Delay Time
0–1300 ms, note
Delay time from the original
sound until the pitch-shifted
sound is heard
Feedback
-98– +98%
Proportion of the pitch-shifted sound
that is to be returned to the input
(negative values invert the phase)
Low Gain
-15– +15 dB
Amount of boost/cut for the low-
frequency range
High Gain
-15– +15 dB
Amount of boost/cut for the high-
frequency range
Balance
D100:0W–D0:100W
Volume balance of the original sound
(D) and pitch-shifted sound (W)
Level
0–127
Output volume
64:
REVERB
Parameter
Value Description
Type
ROOM1, ROOM2,
STAGE1, STAGE2,
HALL1, HALL2
Type of reverb
ROOM1:
dense reverb with
short decay
ROOM2:
sparse reverb with
short decay
STAGE1:
reverb with greater
late reverberation
STAGE2:
reverb with strong
early reflections
HALL1:
reverb with clear rever-
berance
HALL2:
reverb with rich rever-
berance
Pre Delay
0.0–100.0 ms
Adjusts the delay time from the di-
rect sound until the reverb sound
is heard.
Time
0–127
Time length of reverberation
HF Damp
200–8000 Hz,
BYPASS
Adjusts the frequency above which
the reverberant sound will be cut.
As the frequency is set lower,
more of the high frequencies
will be cut, resulting in a softer
and more muted reverberance.
If you do not want to cut the
high frequencies, set this pa-
rameter to BYPASS.
Low Gain
-15– +15 dB
Gain of the low range
High Gain
-15– +15 dB
Gain of the high range
Balance
D100:0W–D0:100W
Volume balance between the direct
sound (D) and the reverb sound (W)
Level
0–127
Output Level
Parameter
Range Explanation
L in
R in
L out
R out
Reverb
2-Band
EQ
Balance W
Balance W
Balance D
Balance D
2-Band
EQ
GW-8_e.book 77 ページ ２００８年４月１日 火曜日 午前１１時４４分