Filter
Top Products
● MSB/LSB (Off, 0 ~ 127)
This parameter lets you designate the MSB/LSB bank select
number. When set to Off (default), the P-150 will not transmit the
bank select number.
Pressing the [ 1/NO] button lets you select Off for MSB/LSB and Program
Change Number. When Off is selected for MSB, LSB will also switch off,
and vice-versa.
Bank Select (PC Table)
BANK PROGRAM MSB LSB
Bank 1 1 ~ 128 1 1
Bank 2 1 ~ 128 1 2
Bank 3 1 ~ 128 1 3
Bank 4 1 ~ 128 1 4
““““
““““
● PROGRAM CHANGE NUMBER (Off, 1 ~ 128)
This parameter lets you designate the program change number
for the currently accessed [SELECT] button. When set to Off, no
program change numbers will be transmitted.
PROGRAM CHANGE RECEIVE
The Program Change Receive function lets you assign
program change receive numbers to the internal voices and
Performances, according to the [SELECT] buttons.
The P-150 can receive a program change message from an
external MIDI device, in order to select any of the 12 voices
or 24 Performances.
At the factory your P-150 was preset so that each [SELECT]
button will receive the program change number message
corresponding to the number above the button in Voice
mode (1 ~ 12), followed by subsequent numbers in
Performance mode, for A and B banks (13 ~ 36).
Therefore, when the P-150 is in Voice mode, when an
external controller connected to the P-150 sends a program
change number 1 message, the PIANO 1 voice will be
selected; if it sends a program change number 2 message,
the PIANO 2 voice will be selected, and so on. If it sends a
program change number 13 message, Performance A01 will
be selected; if it sends a program change number 25
message, Performance B01 will be selected, and so on.
Whenever the P-150 receives a program change message, it
will check the program change receive table to determine
whether a voice or Performance has been assigned to the
Received program change number. If so, the main voice will
automatically switch to the voice indicated by the program
change receive table. (If the P-150 is in Dual mode, this will
cause it to shift to Single mode.) If the program change
function has been turned off for that number the message
will simply be ignored.
●
PROGRAM CHANGE NUMBER (1~128)
This parameter lets you designate a program change receive
number. As you step through each one, the SELECT
assignment will appear to the right.
● SELECT ASSIGN
(V01~V12, A01~A12, B01~B12, Off)
This parameter lets you assign which [SELECT] button to assign
to the currently designated Program Change Number.
You can choose a specific Voice button number by holding [VOICE] and
pressing the desired [VOICE SELECT] button. You can choose a specific
Performance A bank button number by holding [PERF. A] and pressing
the desired [PERFORMANCE SELECT] button. You can choose a
specific Performance B bank button number by holding [PERF. B] and
pressing the desired [PERFORMANCE SELECT] button.
Pressing the [ 1/NO] button lets you select Off for Program Change
Number and Select Assign.
■ Channel
The Channel function lets you assign the P-150’s MIDI
transmit and receive channel numbers or status.
When connecting the P-150 to an external MIDI device, such
as a multitimbral tone generator or synthesizer, you will need
to set the P-150’s transmit channel to the same number as
the external device’s receive channel, in order to play the
external instrument with the P-150’s keyboard. Likewise, you
will need to set the P-150’s receive channel to the same
number as an external keyboard’s transmit channel in order
to play the P-150’s internal voices from an external
keyboard. (For more information, see Using MIDI, page 57.)
PC RX 2
1=V01
Program Change number
CHANNEL TRNS 1
TX= 1 RX= 1
PC TX BankMSB 1
V01=( 1/ 1) 1
LSB numberMSB number
PC TX 2
V01=( 1/ 1) 1
Program Change number
PC RX 2
1=V01
Select Assign
47
EDIT MODE