Filter
Top Products
11
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO
AUX SENDS
STEREO AUX RETURNS
4
3
2
5
6
1
PHONES
2
L/R MIX
L/R MIX
1-2
3-4
5-6
7-8
L/R MIX
SOLO
1-2
3-4 5-6 7-8
PHONES
1
PHONES
2
L/R MIX
1
2
3
4
LEVEL
ASSIGN
ASSIGN
ASSIGN
ASSIGN
LEVELLEVEL
PHONES
1
6
+15
OO
U
+15
OO
U
+15
OO
U
+15
OO
U
+15
OO
U
+15
OO
U
+20
OO
U
+20
OO
U
+20
OO
U
+20
OO
U
LR
LR
5
+20
OO
U
+20
OO
U
SOLO
SOLO
SOLO
SOLO
SOLO
SOLO SOLO
LEVEL LEVEL
LEVEL
ASSIGN TO
L/R MIX
SOLO
AUX SEND
3/4
MIX-B
MONITOR
AUX SEND
5/6
EXTERNAL
MONO
TAPE SUB
MASTERS
AUX SEND 1
MASTER
MIX B / MONITOR
PHONES 1
PHONES
LEVEL
SOLO
MIX-B
MONITOR
EXTERNAL
PHONES 2
PHONES
LEVEL
2-TK
MIX-B
L/R MIX
EXTERNAL
SOURCE
MONITOR
CNTRL RM
STUDIO
OPERATING
LEVEL
INDICATOR
AND
TALKBACK
LEVEL LEVELMIX-B
LEVEL
RUDE
SOLO LITE
AUX SEND 2
PHONES
&
STUDIO
+15
OO
U
O
OOOOOO
+15
OO
U
BALANCE
AUX SEND
3/4
AUX SEND
5/6
SOURCESOURCE
SOLO
OO
OO
+15
OO
U
12345678
169101112131415
2417 18 19 20 21 22 23
10
+
7
4
2
0
2
4
7
10
20
30
40
–
LR
10
+
7
4
2
0
2
4
7
10
20
30
40
–
LR
10
+
7
4
2
0
2
4
7
10
20
30
40
–
LR
10
+
7
4
2
0
2
4
7
10
20
30
40
–
LR
10
+
7
4
2
0
2
4
7
10
20
30
40
–
22
10
+
7
4
2
0
2
4
7
10
20
30
40
–
10
+
7
4
2
0
2
4
7
10
20
30
40
–
10
+
7
4
2
0
2
4
7
10
20
30
40
–
LR
MAIN
OR SOLO LEVEL
METERING
Bus Meters 1-8
Directly above each bus fader is a peak-reading
meter displaying the bus output level. Zero (0) on
the meter references a level of +4dBu (1.23 volts
RMS) at the output jack.
NOTE: If the -10dBV switches are engaged at
the Subgroup output jacks, then zero (0) on the
meter references a level of –10dBV at those out-
puts. Note: When any SOLO switch is engaged, the
SUBMASTER meters will be extinguished in order
to divert your attention to the SOLO/MAIN meters
(discussed below).
MAIN OR SOLO LEVEL Meters
The MAIN OR SOLO LEVEL meters display the
L/R Main Mix levels and are similar to the bus
meters, with these exceptions:
• If a SOLO button is depressed, the meters
display the output of the soloed
signals; if not, the meters show the
level of the signal selected by the
MONITOR SOURCE switches. In
other words, you are always meter-
ing what you’re listening to.
IMPORTANT: When the console is
in SOLO mode,
zero (0) on the
SOLO/MAIN
meters references
the actual internal
operating level, or 0dBu (.775v). If
you have just one signal in the main
L/R path and you SOLO it, the meter
level will jump up 4dB. Don’t be
alarmed. If you’re mixing on the L/R
buses, that’s what you’ll meter. If
you’re checking a tape playback,
that’s what you’ll meter. When the
meters are following the monitors
(not in SOLO), zero (0) on the
meter references a level of +4dBu
(1.23 volts RMS) at the main L/R
outputs, just like the submaster
meters.
Note: The solo levels displayed on
the meters are PRE-solo level,
thus giving you an accurate
showing of the total level of the
soloed signals.This is also the way
to set initial console levels. See the
discussion of the SOLO function,
earlier in this section.
• Additional red LEDs per side at
the top of the meter show output
clipping at +28dBu balanced,
+22dBu unbalanced. (You don’t want these
to ever go on. If they do, try pulling down the
L/R master fader a little.)
AUX SENDS
The six auxiliary send outputs each have a
master level control. Like any level control, turn-
ing the knob turns the volume up or down.
However, the gain of the AUX Sends has been
optimized at the unity (center detent) setting
and should not need adjustment.
The output of each bus is available at its AUX
Send Out jack in the jack panel above. Addition-
ally, AUX Sends 3 & 4 and AUX Sends 5 & 6 are
fed as stereo pairs to the two PHONES SOURCE
switching matrices, for headphone cueing
purposes.
LAYOUT
AND
FUNCTION