Filter
Top Products
10
Names and Functions of Controls on Screen
qd GAIN LIMIT and qf OVER GAIN indicators
The sending level from input section is the sum of the
qj INPUT fader and the input fader of the SRP-X700P.
If the SRP-X700P master volume is manipulated and the
sound volume is remotely controlled via the REMOTE
terminal using the GROUP FADER screen and REMOTE
screen respectively, these setup values are also added to the
sum.
You can set the upper limit of the sending level by the
qd GAIN LIMIT to prevent excessive output level using
multiple volume controls. Each click of the [+] or [--] button
increments or decrements the sending level by 1 dB in the
range of +10 dB to –10 dB. You can enter numerical values
directly on the screen.
If the sending level exceeds the GAIN LIMIT value, the actual
sending level is limited to the GAIN LIMIT value and the
qf OVER GAIN indicator lights in red.
qg
–
∞ indicator
If there is no sending sound when muted or when the INPUT
fader is at the
–
∞ level position, the
–
∞ indicator lights in
yellow.
qh FADER select and qj INPUT fader
The qj INPUT fader has the two modes of ACTIVE and
INACTIVE.
To switch the fader mode, click the qh FADER select. The
selected mode lights in yellow. The yellow marker displayed
on the side of the fader indicates the fader position, which is
the sum of the qj INPUT fader setup and the SRP-X700P
input fader setup.
When the sound volume of a specific input channel is to be set
from the REMOTE screen and the GROUP FADER screen,
the fader position determined by the SRP-X700P Master
volume control and the remote control signal via the
REMOTE terminal is indicated.
ACTIVE mode:
ACTIVE mode is used to adjust the reference sound volume
by using SRP-X700P Manager.
You can adjust the qj INPUT fader by dragging the fader
portion.
The audio signal that has passed the INPUT fader on the
INPUT OVERVIEW screen and the OUTPUT fader on the
OUTPUT OVERVIEW screen, is output.
(The INPUT fader and the MASTER volume control of the
SRP-X700P, and REMOTE1 to 6 of the GROUP FADER
screen are bypassed. The sound volume of the output signal
increases by 5 dB in the case of Fig. 1.)
INACTIVE mode:
INACTIVE mode is used to enable the INPUT fader and the
MASTER volume control of the SRP-X700P, and REMOTE1
to 6 of the GROUP FADER screen.
The sound volume is shown by the yellow marker that is
displayed on the side of the faders. The audio signal that has
passed all faders is output.
You cannot adjust the qj INPUT fader in INACTIVE mode.
(The sound volume of the output signal decreases by 25 dB in
the case of Fig. 2.)
Note
• When the FADER select of the SRP-X700P Manager is
switched to ACTIVE for the first time after shipment from
the factory, the INPUT faders are all set to
–
∞ automatically
and the system is muted even if an attempt is made to
increase the sound volume using the INPUT fader or the
MASTER volume control of the SRP-X700P.
Muting is set in order to prevent the system from generating
a large sound abruptly when the FADER select is switched to
ACTIVE in the event of sound volume adjustment for the
first time. Entering muting is not a failure.
Therefore, do not terminate the SRP-X700P Manager or do
not disconnect the USB cable without adjusting the sound
volume.
• A sudden large sound may occur when you switch to
ACTIVE mode while the sound volume is reduced by either
the fader, MASTER volume or from the REMOTE terminal.
Before switching the mode, stop the connected equipments
and check the direction of the microphones.
• The mode of the INPUT fader and the mode of the OUTPUT
fader are interlocked and so are switched together.
qk LINE4 input select button
LINE4 has the six input channel terminals of A to F.
You can select a input channel from the six channels using this
button. The selected button lights in green.
INPUT OUTPUT
INPUT fader
of the
SRP-X700P
INPUT fader
on the INPUT
OVERVIEW
screen
OUTPUT fader
on the OUTPUT
OVERVIEW
screen
REMOTE1
to
6
of the GROUP
FADER screen
Signal flow
–
∞
–25
–15
–5
0
+5
+10
–
∞
–25
–15
–5
0
+5
+10
MASTER volume
of the SRP-X700P
Bypass
–
∞
–25
–15
–5
0
+5
+10
–
∞
–25
–15
–5
0
+5
+10
–
∞
–25
–15
–5
0
+5
+10
–
∞
+10
0
–
∞
–25
–15
–5
0
+5
+10
INPUT OUTPUT
INPUT fader
of the
SRP-X700P
INPUT fader
on the INPUT
OVERVIEW
screen
OUTPUT fader
on the OUTPUT
OVERVIEW
screen
REMOTE1
to
6
of the GROUP
FADER screen
Signal flow
MASTER volume
of the SRP-X700P
Fig. 1
Fig. 2